开云体育

Awesome, That still said if anyone has a V3 with it and the appropriate equipment that would be amazing. -- Tim Keller - KE2GKB https://shop.kit-projects.com

hi, ok. I've fixed (hopefully!) the switch wiring for the AGC and I'll go take some measurements soon. -adrian [email protected]> wrote:

hello,frends,i have a problem,i wanth to change settings in the ubitx(is a new ubitx)and when i conect whit all the settings(com port,38400,none,8,one)is connecting but when i try to read from ubitx i

If I could ask for the same measurements that digger took that would be great. The solution here is going to be either modding the ubitx to fix the audio issue or adding an amp for the boards that

i have a ubitx v4 with your AGC board installed. I also live in an amusingly noisy environment and I have relevant testing kit. :-P Let me know what you'd like and I'll go see if I can take some

Sorry... I thought this was the same one I purchased. Mine was: https://www.amazon.com/gp/product/B00MHNQIR2/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 $~24, Prime Shipping, With charger. It

I followed KEGYC's link into Amazon for the Turnigy lipo 11.1v 2200mah 1.5c battery pack, see this question and answer: Question: Does it come with a charger? Answer:? ?come alone without charger;

Fairly inexpensive relays -?https://www.mpja.com/mobile/12VDC-DPDT-DIP-Relay-Axicom/productinfo/32715+RL/

Digger do you have any other uBitxs? I currently do not have a good known noise source (Working on it! but alas the day job has its priority :( ) So it is currently out of my capability to make

Rick:? Web site doesn't say it comes with charger--how does one charge it if it doesn't?? Seems like it might fit my BITX 40.

I have a 4.5ah 11(ish) volt battery I may use.. do you have a voltage regulater you use to maintain 12 volts as the battery discharges?

Now I haven't compared them, but they're dip relays and I use them in my CWid boards. MPJA.com has some for $1.29 ea, under a buck each when on sale. I usually keep no less than 10 on hand.

Popping finals and now nanos on my beater v3 board. Started with 13.8v in...then goofing with biasing. Why?? I don't know. Curiosity and cause the trimmers didn't seem to be responding. Changed them

Yes, I put one of these inside my ubitx20 rev 5.1 (tied down with velcro strips) and it works well.? The battery is fairly compact and comes with its own charger that has a jack that fits the Radio.

The 60mhz version at $124.29 only does 60mhz on sine wave generation, everything else is the same as the 30mhz version at $116.29 Makes sense, they can put a low pass filter on the output to extract a

Banggood has model FY6800 in the 60mhz version (max sine wave output freq) for $124.29? The FY6800 30mhz version does not save you much money. Gets good

My uBITX is due to arrive by the end of the week and, like you, my head is full of ideas from trolling this group and the rest of uBITX on the net..? repeatedly I hear what Evan is saying.. I have an

I wonder whether the O P has used 4k7 resistor between key wire and 5v vcc( blue and green wires)? [email protected] wrote:

For a small pack with limited current, Turnigy makes a ready-built protected 2.2Ah pack for $25 https://www.amazon.com/dp/B00USRD91W/ref=cm_sw_em_r_mt_awdb_4muTCbG8JHMRP Especially for newer

Thanks Vic, I modified the GUI from- ubitx_35E6.tft to ubitx_35_E.tft and its solved now... Non the less I only get half of the nextion screen filled !! Regards, Sourav Sent: 15 April 2019 10:56