开云体育

you willing to try a updated version of the 3.2 interface I made a few changes to make it easier to use

Also check these sites: https://ubitx.net/2018/01/30/bitx40-essential-mods/ http://bitxhacks.blogspot.com/ http://miscdotgeek.com/category/bitx40/ and the FaceBook Group....

Hi Dave..... The majority of them can be found here... https://ubitx.net/2018/01/30/bitx40-essential-mods/ dhassall@...> wrote:

Dear Members, I got caught up in the frenzy of building a 40MBITX when they first came out.? I bought the kit and proceeded to get it going. mounted it on a test board and started wiring it up.?? I

Thank you Malcom. Kevin Sent: Tuesday, July 17, 2018 10:52 AM To: [email protected] Subject: Re: [BITX20] 3.2in Nextion display now looks great. Carlo and Kevin, I bought the tuning knob ( well I

Carlo and Kevin, I bought the tuning knob ( well I bought 3 of them? !!) from this ebay seller

Jacques, Thinking about your idea again. Do you want to use the 2560 in place of the nano? I looked at the schematics and it looks like it should be a 18 line connection to the corresponding pins in

I have the uBITS Ver 4 and matching Blue Cabinet, unbuilt, for sale. Since I started using SDR, I just can't get inthused with a Heteradyne based radio. A friend of mine talked me into buying it,

I know this has been around the block a few times, but we need some help. My BitX40 receives beautifully across the band but we have next to no output power on transmit. ?To get anything above 500mW

if you join the facebook page ubitx you will get alot of info and the 1.095 is released a cw bug has been patched I have done alot of work on the tft/hmi files 2.4-3.5

HI Malcom, could you tell me where you obtained the tuning knob ? thanks, kevin rea k6rea

I did this basic mod and it works fine for me. Try pulling the power plug going to the board. There are 3 wires, one ground and 2 hot wires. One of the hot wires goes directly to the finals and the

Thanks for that dave! Hope you are all ok down there!! I will probably give you a bell when I get around to the download. I'm a complete nugget when it comes to PCs etc. regards....Paul

I can say from the pic that the "RD16HHF1" are fakes! Had my share of buying those fake stuff. Hannes, DL4AAJ Am 17.07.2018 um 18:30 schrieb fr.beckenbauer@...:

Good advice, Jack.? Thanks for sharing it. Cheers. -- Jon Titus, KZ1G Herriman, UT USA

The clone boards are counterfeit when they use the "plus-minus infinity" trademark that Arduino.CC owns.? This has nothing to do with open-source.? Anyone can use open-source code, designs, etc.?

Hi everyone, I tried to do this mod:?https://ubitx.net/2018/02/16/power-amp-fix/ I checked everything for shorts, and a multimeter connected to the power input shows typical capacitor behaviour.

Received what I believe is Version 1 of mBITX in January 2018. Built unit and it worked fine until the TDA2822 audio amp smoked and burned. Replaced TDA2822 and know that it is inserted and soldered

Hello Paul, you need to download KD8CEC SOFTWARE and then transfer it to your 4.3 ubitx I had similar problems but all were resolved with the sioftware,,I use Richard G3 CWI dsp W/N cw filter works

Looks very nice Malcolm, I bought one of the 3.2E inch Nextion displays also, but I don't want to modify my already existing uBitx because it's all laid out for the 16X02 display and it looks good. I