Re: RFI from uBitx TX after AGC and other mods installed
Did you put 100n, 10n, 1n filter capacitors all in parallel on both input and output directly across the 78L05 leads? .
By
Lawrence Galea
·
#53435
·
|
Re: Anyone seen an SSB xmit causing the menu to pop up?
Quite a while ago I was messing with some Nano code, but had my FT-1200 on, too. I grabbed the mike and answered a CQ and I remember the Nano display changing when I activated the mic. It turns out
By
Jack Purdum <jjpurdum@...>
·
#53434
·
|
Re: Anyone seen an SSB xmit causing the menu to pop up?
I'm running on a different battery than the jump box I was using before. It should have sufficient amperage. I'll test it with my bench supply and see if it does it under those conditions. It's odd,
By
Gwen Patton
·
#53433
·
|
Re: RFI from uBitx TX after AGC and other mods installed
I think it would be eaiser to shield the little pcb with foil before moving it due to the interconnect wires. May try that first as the pcb is very small and mounted to the back of the RF Gain pot.
By
Rick Price
·
#53432
·
|
Re: Ubitx and QRP Guys Multi Z Tuner
#ubitx-help
Never mind for now. It would appear that the problem now occurs without the tuner hooked up.? I've got some kind of mic or mic jack problem.? I guess it's just coincidence that it started when I
By
davedt1e@...
·
#53431
·
|
Re: Ubitx and QRP Guys Multi Z Tuner
#ubitx-help
Yes, I have seen similar phenomena. In my case my CW wires to my key were too close to my 50 watt linear. Your tuner is probably radiating a lot of RF. Howard
By
Howard Fidel
·
#53430
·
|
Re: Bitx40 75KHz Spurious, How to solve it.
#bitx40
Correction 500KHz span!
By
Raj vu2zap
·
#53429
·
|
Re: Anyone seen an SSB xmit causing the menu to pop up?
Hi Gwen, I had something similar on both SSB & CW. Part of my problem was my 3amp laptop power supply was shutting down. It reset the radio. I got a 5 amp power supply to fix that issue. After that, I
By
M Garza <mgarza896@...>
·
#53428
·
|
Re: Bitx40 75KHz Spurious, How to solve it.
#bitx40
Akira, I just put my uBitxr4 on the spectrum analyzer and found nothing +-250 Khz. That is 500 Khz BW. I think your measurements are being affected by switch mode power supply in one of the items. Raj
By
Raj vu2zap
·
#53427
·
|
Re: RFI from uBitx TX after AGC and other mods installed
Rick, If it's the PCB what about putting it below the ground plane in the same relative position as the suggested spot next to the RF relays? John KC9OJV
By
John KC9OJV
·
#53426
·
|
Ubitx and QRP Guys Multi Z Tuner
#ubitx-help
Hope this is an appropriate topic for the board. Just built he QRP Guys Multi Z tuner and hooked it up to the Ubitx.? The Ubitx goes straight into TX on power up.? I was very careful in building the
By
davedt1e@...
·
#53425
·
|
Re: uBITX Version 4 first attempt
#ubitx-help
#ubitx
let someone from the competent radio engineers check my method and tell here for everyone if it works.
By
Andy V. Borisenko <rw9rn@...>
·
#53424
·
|
Re: uBITX Version 4 first attempt
#ubitx-help
#ubitx
Richard, good afternoon! note, there are many people here who consider themselves radio engineers. but no one gives you advice on calibration. I'll try with my bad English to tell you how to properly
By
Andy V. Borisenko <rw9rn@...>
·
#53423
·
|
Re: Nextion Display programming, extension cable
That looks neat.. -- Allen ?Merrell
By
Allen Merrell
·
#53422
·
|
Re: TX frequency? of uBitx at CWL and CWU mode
#ubitxcw
Akira-san :? The uBITX display frequency in CWU/CWL is the RX frequency not the TX frequency. The norm in CW on most commercial rigs is to always display the TX frequency. You can however set the RX
By
Michael VE3WMB
·
#53421
·
|
Re: Anyone seen an SSB xmit causing the menu to pop up?
learnt a point Farhan jee. Regards MVS Sarma
By
MVS Sarma
·
#53420
·
|
Re: Bitx (40) agc and muting
from junction r111/r113 solder a 1n4148 diode direct to the 12volt rail (LM368 is now alltime connected with 12volt) 73 elmar-dl2qa Gesendet: Sonntag, 01. Juli 2018 um 14:15 Uhr Von: 4Z1NT
By
Elmar V?ller <dl2qa@...>
·
#53419
·
|
Re: RFI from uBitx TX after AGC and other mods installed
John, Don, others, Yesterday I attached a 78L05 (TO220) directly to the back of the AGC board that is mounted to the RF gain control on the front panel. Bypassed all power leads and ran a separate
By
Rick Price
·
#53418
·
|
Re: Bitx (40) agc and muting
When you say solder 1n4148 t0 +12v not RX, which one are we talking about?
By
4Z1NT
·
#53417
·
|
Re: Bitx (40) agc and muting
Hello Derrick, here is more info. please look at the picture . hope it is visible. if you have any question --give me a shout. Gesendet: Sonntag, 01. Juli 2018 um 13:52 Uhr Von: "Derrick Young"
By
Elmar V?ller <dl2qa@...>
·
#53416
·
|