开云体育

Easiest to just clip all the pins to remove the old nano, then extract the pins one by one using a soldering iron and needle nose pliers.

You know, I’d love to see the uBITx as a kit.? In fact, I’d take it as just a bag of parts and a circuit board… skip the assembly and testing.? I’d do that myself.? What that would do is

No the power transformer T11. The ?BN61-002 shows lower loss than the BN43 equivalent.??It’s 1:2.? I’m gonna try to cap couple it so it doesn’t carry the DC as soon as my iron heats up.?

Yes it is.? But then you get what you pay for. *Dr. William J. Schmidt - K9HZ*? *From:* [email protected] [mailto:[email protected]] *On Behalf Of* Nick VK4PLN *Sent:* Thursday, May 17, 2018 12:43 AM

Think of it this way… if you spent $9 US on a pair of RD16HHF1 FETS… then what’s another $6.50 US to bring them to full life?? Save the 202 for the choke. ? *?* *Dr. William J. Schmidt -

I use RD16HHF1s… I think you will find that the BN61-002 wound 1:2 runs cool. ? *?* *Dr. William J. Schmidt - K9HZ *? *From:* [email protected] [mailto:[email protected]] *On Behalf Of* Skip Davis

Excellent !? Additional Data is always good!? ? I will be at Dayton starting today.? Spot 7533 for those who want to stop by and say Hi (although you may be talking to my beautiful wife, while

Joe, Thanks as I also have one of those encoders and planned to use it.? My plan was to make the changes you have done. Saves me a bit of testing. The STM will make doing color display easier and

The Arduino board is soldered to the other board. I used a hot air gun on the pins connected to the other board. Then one of the solder sucking guns out clean out the holes.If you get an Arduino board

Don't know enough about the minipa 70 to comment.? Is there a circuit out there to look at? The Wa2EBY I have has run at 65W (40M) brick on key mode for nearly 20M before I called it good.? Only

The Mac can have trouble talking to the CH340 USB chip on the Nano clones requires a special driver.? Here's on possible solution plucked from a very long thread: ?

Hey Joe, good to see you taking on the uBitx! I don't think Farhan has not released mechanical data, but here's gerbers for a Raduino replacement that Nik may have gotten right through careful

Hi Allison, It powers on but its unresponsive to any input from the rotary controller or the funktion button. When pressing the reset button it blinks for s second showing the version of the sofware

Most dynamic mics are like speakers with 50-500 ohm voice coils, Most are not very compact with an OD of 10MM and up to as large as 30mm.? That is at least true for ones I have. Electret mics ar

Failure to connect may be due to wrong USB driver, wrong board selected (under tools), wrong port selected (under tools) or maybe even a bad cable. I will not suggest more than at for now as for me it

Rogier, Please be aware that on Windows systems it may be necessary to load a driver program. Apparently there are two variations of Arduino Nano, and one of them is not automatically supported with

The Raduino board is NOT an arduino board. The processor chip on the board (NANO) is an arduino but the Raduino board is NOT from arduino. rOn

Thanks these instructions will get me going. You might have seen that I have been strugling to get my uBitx to work and I am now certain that I have a failed Raduino board since it doesn't even want

Thank you for your reply.. What is difference between dynamic mic and electret condenser mic? Do they look a like in shape? The one I bought is look like this..

I think that is a very useful exercise by that person. https://drive.google.com/file/d/1PBK-cdn4-9EunFHl2bXBSUnx1RFP9Z_f/edit 73, John (VK2ETA)