开云体育

Problem with my scratch-built uBitx. Can’t get more than about 4W PEP on 40m, and 1W PEP on 20m without having what I think is the PA breaking into oscillation. SYMPTOMS: SSB: When I key the PTT

Should have worded the opening a bit different. This new board replaces the Raduino and makes NO repeat NO modifications to the main uBITX transceiver's main board. It only adds much more programming

Hi Ash, I vote for keeping the out-of-the-box firmware simple. I’m enjoying playing with KD8CEC’s version but prefer the ‘feel’ of yours, especially tuning. Thanks for some fine work on the

Ian, I am glad this got your attention. The software if very impressive. I think we can take forward the attenuation hack (I really can't describe it as anything but a beautiful hack) worked very well

Mike, I may be missing something basic here.? Or maybe I need to clarify what I liked about Ashhar's general coverage behavior.? Ian's manual says: "When? Band? Select? is? displayed,? by?

Ashhar Farhan and all I have seen various opinions of various OMs. I think that even being mentioned is an honor. Whether the firmware will be replaced to v1.06 or not, retained original firmware, or

W0EB/W2CTX and N5IB are announcing the upcoming release of a complete new board for the uBITX transceiver that utilized the PJRC Teensy 3.6 as the micro-controller rather than the Arduino NANO. We

Does the cap provide output leveling or increased output from 80m to 10m? I mainly operate 80m, 40m, and a little 20m. The output there seems to be fine for what I do. tim ab0wr "K9HZ"

Hi all,? I'm having trouble getting the CP2102 chip on my Radunio to be recognized by my Mac Mini, however the Arduino IDE program can see my other Arduino boards and my FTDI based USB to Serial

Or WSPR code… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa Grand Piton – J68HZ

Partition the code so the keyer or CAT stuff or whatever can be ifdef'd out. Then experimenters will have plenty of room to play. Jerry

I just put mine at the base of T11 but there are many ways of doing it depending the type of part you use... I also replaced T11 but let's not go there yet. Dr. William J. Schmidt - K9HZ J68HZ 8P6HK

How do you recommend doing that? A disc ceramic between IRF510 pins? Can you get an smd cap between the pins on the bottom of the ckt board? tim ab0wr "K9HZ" <bill@...> wrote:

I would think you could get more than 5watts out on 80m. You might still try an antenna tuner between your ubitx and the dummy load. It's possible the ubitx wants something other than a 50ohm

Personally, I think there is great value in maintaining the original "factory" code base, simply because this is a hacker's dream! Delivering with your original core software takes nothing away from

Ian’s firmware has always had the option of toggling to general coverage RX (at least since v0.33 by my notes). How to do this is documented in the manual. M

Ashhar, I have been using Ian's firmware because of the added features, especially CAT.? But, if possible, I would like to have the choice to use your preference?for general coverage when changing

Thanks Alyson for that information! I guess if you take any antenna with 15 dB of gain and then throw in 3DB of loss, you still have 12 DB of gain! In order to make my non-resonant dipoles tune with

Yes, it is a model. 1. One could measure the power sent to the antenna and then measure the RF voltage across the load resistor, and compute the power dissipated on the load resistor presuming that it

No I haven’t Bill I’ll try that later tonight when I get some time. Right now I’m taking a break from outside yard work :) Skip Davis, NC9O