开云体育

Ordered mine on January 9th and it arrived in W2-land via DHL on March 9th. 73, Gordon Beattie, W2TTT Get Outlook for Android

Not yet, I have decided to re-model the case, and install my RaduinoI2C board... Also mounted a swr bridge... Gonna be a nice little rig if I get reasonable results from the PA mod.. 73..

Good thought, Marco. But most. if not all variable VR's have a fixed or lesser VA output. IF you lower the voltage, usually the available amperage goes down as well... I use two in my bench supply,

Shaun, The ubitx doesn't have a balanced mic input, i.e. mic leads that don't have one connected directly to system ground. In a balanced feed the shield wire would be the system ground and would act

Works... Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa Grand Piton – J68HZ

This is the modification I came up with to implement a 7805 to supply the TDA2822. Please check it over for errors.? One trace cut and scrape a little off the board and solder in the 7805. Ron W7HD

I received my uBitx today ordered January 8, 2018 notice of being shipped March 6, 2018 received March 9, 2018 john kg9dk

Nice… any power to it yet? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa Grand

Pete, Maybe some more experimentation with the capacitor value is needed. The diode has some finite forward resistance so it will take some small amount of time for the cap to charge up. I originally

" If you tear a lot of communication mics apart you will see that the mic element is wired through the PTT switch on most of them." That is exactly what I would expect and have seen in the past, but

Thank John, moving the Drain to R70 (changed to 510) helped restore my volume. However, I am getting the pop going key down RX to TX but no pop going from TX to RX. So the MOSFET is not muting quite

Thanks Ian. For a great updated to include WSPR, It was a surprise. Philip G7JUR.

Walter, What voltage are you feeding this with? I assume it is more than 24v in order for you to have a 24v position. If you are running in the 10 volt position, for instance, that would be drop of at

Jerry, Having a live mic with a separate, unassociated PTT switch can lead to inadvertent transmissions if the PTT gets operated accidentally. If the mic is not live all the time then all you transmit

whats the latest on the new w8tee lcd vfo for the ubitx ?

Here's a starting point on web resources regarding this big/little endian stuff in case you're curious. ? ??https://stackoverflow.com/questions/13994674/how-to-write-endian-agnostic-c-c-code But

I found a much better place to connect the drain of the MOSFET. First I replaced R70 with a 510 ohm resistor that I happened to have in the same footprint. Then I connected the MOSFET drain to the

Mods so far, in tested.

uBiTx on air....Tks Ian / Philip Carlos 2018-03-09 21:12 GMT+01:00 Carlos E. Wenzel <ik2yra@...>: -- Carlos Wenzel ik2yra@... +39-3284684518 Skype: IK2YRA

So simple.... TKS Philip Carlos 2018-03-09 21:01 GMT+01:00 Philip <philip.g7jur@...>: -- Carlos Wenzel ik2yra@... +39-3284684518 Skype: IK2YRA