开云体育

Whether or not you can is indicated on the card. Whatever the carrier checked or indicated on the card is what matters, even if they erred. Vince. -- Michigan VHF Corp. http://www.nobucks.net/

But I ordered Free Shipping, came by carrier, not US PO? Mike -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399 (909) 918-0058 PayPal ID "MotDog@..." Mike@...

+1, Andy. Greg, KC8HXO Sent from my Linux device

I don't really know if I can leave a signed card in the mailbox, will post again in this thread if I find out and nobody else has posted that information. I'll pick it up at the post office since it's

I ordered with FREE Shipping, still came in a week.? They left it at the Door on Sunday!? No Sign Nothing! That just might be my driver, and it IS Christmas Time.? I even see the US Post Office

I think this has been explained before. With the Tx path un-powered, the diodes in those transistors' Collectors effectively open-circuit that side - the output impedance of the Tx-path circuity

Just use the the Amps going in the Receive Direction.? You can tell, they get their power on Receive ( the Isolation Diode and resistor).? You could "Can" that circuit and make them universal.? I

Does it have to be signed for in person? Or can you sign the little card and just leave it in the box with the flag up? Vince.

And for artists, perhaps. But, aren't we all kids and artists, actually? Just playing and having fun with our bitx's :=) 73, Allard PE1NWL

As I said previously, Paypal gave a 10 digit tracking number, which is DHL. DHL said they had handed it off to the US Postal Service since we are so remote, and gave me a 30 digit USPS tracking

It is brown wire pin 6 on the connector of Raduino and connects to Bump Switch on Encoder. -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399 (909) 918-0058 PayPal ID "MotDog@..."

It is in Preferences top left of IDE. Mike, who actually Likes Arduino IDE, except the Word "Sketch".? Sketches are for Kids, like Trix! The only compilers I really got along with was MicroChips

I am still adding a Tune Button as I did on BitX.? It offsets the Mixer for some RF Drive and plunks in the Xmit Relay. I am running out of panel space, the Key Jack is going on the back.? I also

Hi, I've just released raduino v2.02 for BitX40, download it from https://github.com/amunters/bitx40-raduino-v2 In this release: * Fixed another bug in the calibration procedure * Slightly changed the

The first blow up was (I thought) I put the I2C connector backwards on the LCD.? It is not polarized there. I hard wired with shrink that end,? and the other end is Molex polarized. Then everything

Did you calibrate the VFO and BFO? The BFO signal is now generated by the si5351, so if it's not calibrated precisely then the BFO frequency will be off, resulting in an unnatural (sharp or dull)

Good question. But since Mike was not specific, I'll assume it was his error and not something I need to know about. Perhaps 12 power from the uBitx got wired into some MegaPro signal pin.? Jerry,

After looking at the latest code, I think you are right Jack. It seems the red wire is assigned as the function button and its going to the encoder switch. He must have abandoned seperate function

The earlier version used a combination of pot and function button. This has been replaced by the rotary encoder with integral pushbutton - a much better solution. We have just one spare I/O (an

You'd only need one of the amplifiers in each bi-directional pair.? My take (I'm also working on an RX build) is that since everything has 50Ω in/out, we can think in 'module' terms.? Here's a look