开云体育

Hi Dexter,I have successfully worked ?zl with my bitx40, he was only running 100w and an inverted vee, my report was 55, just running barefoot 7 watts into a butternut hf9v sitting on a pontoon

Hi Dex...have a listen around 7.178 MHz for VE6RAC. I worked hime 1,600 miles with 7 watts BITX40 from Ontario. Also hearing New Brunswick Canada on the east coast so my prop is east west right now

Any activity in ZL/VK? Maybe ZLs should be listening around 9:30 on to catch the VKs? My kit has heard CW around 7013 at times, and a VK4 further up (once), among heaps of QRM, but nothing workable or

just worked VE6RAC Mike in Calgary on 7.178 qrp with BITX40 so 40M is open to west from Ontario! Back to 7.277

listening 7.277 and 7.285 alternately.

I can go on if you tell me freq. Kd2nou Ben KD2NOU

Anybody on tonight? 7:15pm local? 0015 HRS UTC. If so what frequency?

Hi John, Thanks for notifying. It's only a display issue. The VFO can really tune beyond 10Mhz, but the display gets messed up because of the extra digit. I'll try to improve that in the next version.

If 12V, maybe go to 3.3 to 4.7K.? Leds are fairly bright at a couple of ma? Mike -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399 (909) 918-0058 PayPal ID "MotDog@..."

Mike beat me to it, and with better. Resistor first, then wire to diode/s (raw voltage to flying leads not the best idea! :) 73!

Easy, Ben! Consult the circuit diagram. Relay K1 is supplied with +12V. It then feeds either +RX or +TX as the case may be. The underside of the board has the pads to connect to, either to individual

Hi, just a quick question about the frequency range, i installed ver 1.26, all ok, then changed the upper and lower frequency range to 3mhz and 15.5mhz. I had hoped to be able to rx 30 and 20 metres

Just go to the Rx and Tx lines that control the direction of the amps.? Put a 1K to each Led from them. I think that is what you asked? 73's Mike, WA6ISP -- Mike Hagen, WA6ISP 10917 Bryant Street

Hi Everyone, Could anybody tell me a way I can pull voltage from the board for an LED on RX and then pull voltage from the board for a TX LED and turn off the RX LED? Thanks Ben KD2NOU -- Ben KD2NOU

Probably these? #include "si5351.h" #include <Rotary.h> Remember the complaint the external SI library eats memory? That's why it is internal on newer versions. Mike, WA6ISP

yes, now it compiles: "Build-Optionen wurden ver?ndert, alles wird neu kompiliert Der Sketch verwendet 15464 Bytes (50%) des Programmspeicherplatzes. Das Maximum sind 30720 Bytes. Globale Variablen

OK, comment out LCD.H and // LCD Backlight ON //lcd.setBacklightPin(BACKLIGHT_PIN,POSITIVE); //lcd.setBacklight(HIGH); Now it compiles here? Look like those functions are in some other library other

Here are the libraries installed?? There are 2 screen dumps shown. LCD.h has to be somewhere? Maybe addons from Adafruit? Mike, WA6ISP -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399

Yes, does not compile here if I comment out LCD.h. I am trying to find LCD.h. ??? Have not found it yet? Mike -- Mike Hagen, WA6ISP 10917 Bryant Street Yucaipa, Ca. 92399 (909) 918-0058 PayPal ID

Thanks Mike I will give it a try. Also, I hate auto correct on this tablet. It makes me look illiterate!