Re: W8TEE TFT/VFO Board from FDIM talk
Jack¡ Would you be able to ship to N Ireland, and if so what would the postage be?..If reasonable I would like one Charlie GI4FUE Sent: 26 May 2017 22:10 To: [email protected] Subject: [BITX20] W8TEE
By
Charlie Morrison
·
#27096
·
|
Re: W8TEE TFT/VFO Board from FDIM talk
Jack, I would like 2 boards when/if available. Mike K5ESS Sent: Friday, May 26, 2017 4:10 PM To: [email protected] Subject: [BITX20] W8TEE TFT/VFO Board from FDIM talk All: Attached is the manual that
By
K5ESS
·
#27095
·
|
Re: W8TEE TFT/VFO Board from FDIM talk
I'm still good for 3 Jack. regards, Richard W2KAP
By
richard kappler <richkappler@...>
·
#27094
·
|
Re: W8TEE TFT/VFO Board from FDIM talk
Jack , I would also like 3 boards if possible, should there be an extra I would take 4, this is going to be fun! 73 de Seth - W8FG [email protected]> wrote:
By
Seth Lavinder W8FG
·
#27093
·
|
Re: BITX40
I didn't seem to get any documentation with mine. So I had to make do by going to the website while I was building and I also have some friends in IRC on the ##rtlsdr channel Sent from my iPhone
By
Joe Puma <kd2nfc@...>
·
#27092
·
|
Re: W8TEE TFT/VFO Board from FDIM talk
Jack your manual is outstanding.? I look forward to your post with ordering information for the board.? Now I just need to figure out $4.80 worth of something I need from Tayda to make minimum when
By
Doug W
·
#27091
·
|
Re: W8TEE TFT/VFO Board from FDIM talk
Jack, I need 3 v/r Fred W4JLE Sent: Friday, May 26, 2017 17:10 To: [email protected] Subject: [BITX20] W8TEE TFT/VFO Board from FDIM talk All: Attached is the manual that will go with the TFT/VFO PCB
By
Dr Fred Hambrecht
·
#27090
·
|
Re: contents of kit
Happy Bitx'ing Sent from my iPhone
By
Joe Puma <kd2nfc@...>
·
#27089
·
|
Re: BITX40
Thank you! Now why didn't I see that when I went there the other day? I remember everything else about the page... Thanks! Vince. -- Michigan VHF Corp. http://www.nobucks.net/ http://www.CDupe.com/
By
Vince Vielhaber <vev@...>
·
#27088
·
|
Re: BITX40
http://www.hfsigs.com/bitx40v3_wireup.html ( http://www.hfsigs.com/bitx40v3_wireup.html ) http://www.hfsigs.com/bitx40v3_circuit.html
By
Doug W
·
#27087
·
|
Re: I find the Transmit audio is a bit muffled has anyone else found this?
Thanks all for the replies. Peter in fact contacted me and suggested I look up his youtube video on the subject. I have sucessfully modded the 40 meter one by adding 27pf on place of the 47pf as well
By
vk3xl@...
·
#27086
·
|
BITX40
I'm about to order a BITX40 from HF Signals. Does it come with the documentation (schematic, parts layout, etc) or is it available for download somewhere? I looked in the Files section but there
By
Vince Vielhaber <vev@...>
·
#27085
·
|
Re: I find the Transmit audio is a bit muffled has anyone else found this?
"Gerardo" =Gerard. ?Grrrr autocomplete!
By
Jamie Rolfe
·
#27084
·
|
Re: I find the Transmit audio is a bit muffled has anyone else found this?
Hi Mike *I did the mods Gerardo referred to and it worked great. ?Vk3ye suggests 27pf, I had 3 x 10pf laying around so I just stacked them... Close enough. ?Good reports. Receive audio sounds better
By
Jamie Rolfe
·
#27083
·
|
W8TEE TFT/VFO Board from FDIM talk
All: Attached is the manual that will go with the TFT/VFO PCB that I am making available. I suggest that you read through it to determine if you want to build it. The manual only talks about the
By
Jack Purdum <econjack@...>
·
#27082
·
|
Hooah
Received my BITX40 today. Will be looking for contacts from out of the Savannah, Ga. area...see you guys on the air...hopefully soon.
By
David Woodward
·
#27081
·
|
Re: Step by step raduino software install instructions
My WIN 10 desktop and laptop do not see the CH340 nanos. I may have a bad USB connector on the board because the same USB cable works with my FTDI nanos. 73 Ken VA3ABN
By
Ken
·
#27080
·
|
Re: Step by step raduino software install instructions
The original CH340 drivers can be found at a link on the manufacturer's page here: http://www.wch.cn/product/CH340.html On a Win 8 machine I found that I had to plug in the NANO before installing the
By
Bob
·
#27079
·
|
Re: Step by step raduino software install instructions
Thanks, Michael! I disabled the power saving feature. We'll see what happens. Jack, W8TEE To: [email protected] Sent: Friday, May 26, 2017 2:54 PM Subject: Re: [BITX20] Step by step raduino software
By
Jack Purdum <econjack@...>
·
#27078
·
|
Re: contents of kit
Got mine today also....kf4wbj the SMD And I believe it's probably a spare I don't know. Or maybe to include for the old VFO method. experience with everyone.
By
David Woodward
·
#27077
·
|