开云体育

The issue isn't what the folks at HF Signals worship or recognize, it's that their Chinese Suppliers they rely on basically shutdown operations for a week to celebrate, throwing off production

Try using a different board.? The newer Nanos have a different bootloader that works at a higher speed interface. 73 Evan AC9TU

i am trying to upload reedsbn firmware in my ubitx 6.1. i got below error messages in arduino ide. ''Arduino: 1.8.9 (Windows 10), Board: "Arduino Nano, ATmega328P (Old Bootloader)" Sketch uses 30558

ps.: As usual, I feed the PA from a reverse current-limiting power supply. I do this because I don't like to touch a soldering iron often for repairs. In my case, the PA receives 12.5V and I limit the

I have an MX-P150 running, I send out a maximum of 60 Watts in FT8 mode, when the input is approx. 6 Watts. The sbitx drive=9-10 (depending on the wave propagation) at 14 MHz, while the drive=20-22 at

Is the anyone running a Xiegu XPA125B with there Sbitx v4.4 with Jeff's QRO board? If so can you give me the "run down" do's/don'ts? Drive power ect ect... The QRO board should be here today ?

Sorry, I think I worded it wrong. I ask that you write about your experiences with this complex callsign problem on the Discord JJ page and that there is a solution to fix the problem, because you

Yeah, I, for one, have had stellar service from Farhan. Also, he's in India, not China, but I didn't know and don't WANT to know what he and his crew worship or the holidays they recognize. That's

Please make it stop. This and the "add me to the list" BS. [email protected]> wrote:

I can understand both sides of this. However, I do believe that a bit of transparency, more information and more frequent updates, from HF Signals would make everyone happier all around. Lately I

I figure that it gets here when it gets here.? Chinese New Year is a pretty major disruption so I accept the estimated shipping dates with a large pinch of salt.? Personally, I'd prefer to wait and

That's not very nice...... Give these folks a little grace. I am not one of the 250 but I look forward to ordering regardless of your local club newspaper report. --Gary Farley KQ4SDM To:

What, that a small company had some delays shipping a brand-new radio? I think the ham community, in general is more patient/forgiving than you apparently think. Heck, Flex had delays shipping their

Seriously? It is March 7th, the last update said to expect shipment this week - and this week literally just ended. Was a target missed, yes, but what is the problem, really? When the radios ship,

I'm another one of the 250.? I have quite a collection of QRP and near-QRP radios (sBit, etc.) and am reviewing them for the local club newspaper.? This wouldn't look good if I mentioned it with

good movie how to desolder multi via-hole components, also relays: https://youtu.be/Vou2xlJkuoU?si=BaX7Vr33kL81YsvT regards

Encoders are cheap enough that you could get a lifetime supply, and swap it out and see if that fixes it. https://a.co/d/gJcHhrS

Hi to the group -- The rotary encoder skips during rotation. I've seen this before on other project but can't remember how it is fixed. Should I replace the encoder ? Thanks in advance -- Rick W7RNB

We were told in Feb. Feb. Passed, nothing shipped We were told the first of this week,? in March.? ?So far nothing shipped and no communication sent to list so that the 250 people who ordered know

Gordon: Is I possible to download the CW (Decode / Encode / Keyer) portion of the sbitx software and play with these functions on a Pi 5 as I am not ready (funds) to make the leap to the radio