开云体育

JJ or whoever can answer my Newby questions, Sorry to being such a PITA with all my questions. So I just copy the contents of the data directoy from the home/sbitx/data, data directory on my current

ps.: Yes, I see you are asking about the broadcast side. When I started to look for the cause of this error, I found that the sound control panel was also open during transmission and the sound level

Peter, In the pictures above, you can see that I set the sound level coming out of the radio *on the sbitx gtk screen* that controls the radio, and that sound level goes into the jtdx as the

Hi Gyula,? where are you adjusting the audio levels for JTDX? I tried Pulseaudio and alsamixer, but could not get the output audio to increase. For now, the sbitx does not have an ALC meter, so it

The OS should not affect the way the software runs. Can you make the power setting change using a wheel mouse? That's weird that it won't go below 26. Sometimes you have to toggle something like going

sudo apt install ntp sudo apt install ntpdate sudo ntpdate -u time.nist.gov Type ntpstat until it says the time is synchronized 6 get the latest version of sbitx from the github git reset

ok i get the nag about user_settings.ini to rename.. i renamed.. now ./update gives me the same nag.. vince

Ok..now to update the software...ugg.

https://youtube.com/shorts/ 4Ad3mdo2IzQ?si= nka4DvhYJud2N3f2 ( https://youtube.com/shorts/4Ad3mdo2IzQ?si=nka4DvhYJud2N3f2 ) https://www.youtube.com/channel/uc1jifv68aktxyvyjmqscfpa Something to

Thanks, Mark, for your enthusiasm!? I am consulting with a friend of mine that is a member of the same makerspace I'm in, and he's offered to help. I am more familiar with 2D so am considering seeing

The t-slot frame is temporary until I can fit it into a portable hardcase with a proper front panel. The wood is an interesting look too, and I think it fits the desktop style use case. How did you

oops.. i have a signal generator, and with about 100-200mv i can get a signal through to see it on the spectrum display. I was able to changed bands.? Checked all bands and sig gen can get through,

Here is the "manual" for the board: https://youtu.be/dyV31qtW7xI?si=6zvvS7erpavfYFmy The circuit diagram is on https://github.com/afarhan/sbitx

Ok, Lots of progress... 1.? Mod that Ashar sent is all wired in..RTC included.. 2.? Raspberry Pi comes up, all good on that side.? sbix comes up when launched, as does FLdigi.. 3.? Band switching

Hello Glenn Schematic of the sBitx v 3 is available at the HFsignals web site. Please follow it. The 3 pin RMC is for speaker. The two pin RMC is for power supply to display (J11) and for internal

Good evening JJ. trie the manual adjustment. no dice. That is set by the software on each startup. I'll poke some more. that may just be the way it works.. I am curious though, are you seeing the same

Hello I just received my boards only v3 kit. I have my own 7" pi display and rpi4. I am looking for a board diagram and or schematic for the v3 board. The kit came with some wire connectors but

If it was heat, this weekend would have been great to run hot.? I was out in a park (to get away from local rfi) to try to get DX contacts for the big contest weekend.? It was quite cold outside and

Good lord, is that green bar, tractor feed, paper it's sitting on? Wow, that's a blast from the past! Ken, N2VIP

I just noticed one bug in this design…. The pocket for the encoder board was designed upside down. This put the vfo knob at the top and function knob at the bottom. There is enough cable to flip it