开云体育

I'll help you: the files are in the */home/pi/sbitx/data/* folder and you can copy them to a usb stick with the file manager. Or you can click on the file to view its contents and take a picture of it

Ashhar, I have the same problem with the new software when running ft8. -- Bob AA4FJ

I have added the .gitignore to the repo. can someone run ./update and see if it works on your end? wrote:

This is a brand new SBITX transceiver made in India by Farhan. This transceiver runs 20 to 40 W output, depending on the band covers, all modes including digital modes and includes a built-in

Hi Ashhar, That sounds like what'is happening.? When I change the frequency, I definately hear a relay change of state. Also, before the recent software upgrade, when I powered down the sBitx, I

Hi Gyula, Thank you for reply, But I'm not sure that it will help, as today I investigate the routine of the Sbitx . As I'm not so familiar with the Raspberry pi "batch file", I just explain what I

https://www.atlassian.com/git/tutorials/saving-changes/gitignore Hope this helps Regards Daniel [email protected]> wrote:

Hi Nir, You can find the information you are looking for on www.cqsstv.com ( https://www.cqsstv.com/ ). There is a problem, because if you haven't downloaded the qsstv_9.5.3.tar.gz (

Git ignore https://www.deployhq.com/git/ignoring-files#:~:text=Creating%20an%20ignore%20file,a%20file%20should%20be%20ignored .

Hi Steve, I do not have a v2 board, but Ashhar Farhan posted a picture on April 10.? It shows the SWR bridge as part of the mainboard, not a daughterboard.? This includes the ATTiny85: The circuit

Hello all I have an april v2 sbitz v2 coming my way. being pre hamvention does not have the swr circuit in it..I am looking to find a picture of where in the v2 the swr board was installed and wiring

I need help, my knowledge of how git commands work is very poor, though I understand how it works very well (story of my life!). This is the problem: The hw_settings.ini was earlier checked into the

Scott, the problem could be in the software. What is probably happening is that the relays need to be switched back to the appropriate LPF after tx to rx transition is complete. - f wrote:

Hi Guys, I've run into a curious problem.? I have been running WSJT-X with my sBitx DE successfully for months.? My DE feeds a pair of 20M Hamsticks in a dipole arrangement through a ATU-100EXT

Is it possible that I am doing something wrong? I performed the Sbitx v2 software operations published on May 4, 2023 as described. First on May 6, when I connected the output to a 250W heatsink

Most important is that the transmit frequency for a channel is accurate with minimal drift.

Hello. I want to configure the QSSTV, for in\out sound, but no success. The default as all you know Is the Fldigi, that run automatically. To use the Qsstv, I am log out from FLdigi , and run The

Success!? I found the correct file I need (for uBitx V6) and downloaded it once again.? This time it uploaded to the nano? right away.? Tomorrow I will stick the new nano in the radio.? Thanks

Jim, You are running a uBITX V6, correct? Then you should use Nano3_CECV2_R56_Nextion_LocalS.hex. Try first uploading the 1.2 version and then without unplugging it, upload the v2 file. I can't

Progress has been made.? I was able to connect and upload CEC V1.2 to one of the new nanos.? (And it did connect at 57600).? However, I was not able to upload V2.? Also I didn't see which file I