开云体育

i have a few PCBs to giveaway. I am asking p&p for it. Letter unsigned 2,50 Euro Letter signed 5,00 Euro Two PCBs with no components. ?Payment via Paypal Friends only. Drop me an email for paypal

That happened to me and I solved it through proper grounding and ferrit clamped over the coax going into the rig.? I used 2 of the clamp on type.? Need to get them that fit over the coax, or else an

Guy, what are you using for a power supply? If the voltage drops you might be getting that intermittent cycling you describe. If that is a v4 uBitX board, the audio output is very low as delivered. I

An update: Adding a pull-up 2.2K resistor between the 5v pin and the PTT line stopped the PTT cycling when the microphone was plugged in, so that is all working as expected, now. However, when

I do have a couple of supplies that will do. One is a 2.5 or 3 amp adjustable. WE used it for servicing radios. And another is a 4 or 5 amp. I need to see if it is regulated or not. I can add

Note: I have, like others, injected RF and manually swept the frequency through from 1 to 30 MHz. There is a horrible dip at the lower end i.e. 40 MHz is really low compared to 20 MHz. Yes I realize

Same horrible problem! I have good output on all other bands - the best is 20 meters. However, the 40 meter band is really low! I have shelved this project (as this has dun my head in) for a while

“the 12 mhz from the bfo leaks into the local oscillator. A 5uh in series with a 47 pf across C202 of the LPF will suppress it.” Is this a recommended mod?

Ive ordered the display and im looking at arduinos as we speak. Ill be more than happy to keep you posted on everything. Good luck with the new job and thanks for all your help. If you hear of, or

The nano would fit because the display is dead and the dds is not working. They also picked up an LCD. I fully believe that one of the two are bad. I'm excited to find out which. I started doing tech

It may be but it all happened at the same time. I know anything can happen but ive been soldering for a lot of years Sent from Mail for Windows 10 Sent: Tuesday, January 29, 2019 12:25 AM To:

I suspect the nano soldering for no audio.

Im thinking the same thing. Thanks for the help Sent from Mail for Windows 10 Sent: Tuesday, January 29, 2019 12:11 AM To: [email protected] Subject: Re: [BITX20] display not working I really think the

I really think the nano has died. They are cheap anyway. Put an aftermarket firmware on it and swap the display if you get it first. Since you have no audio, Im betting the nano is dead. I could be

Its telling me cant connect to board because its out of sync Sent from Mail for Windows 10 Sent: Tuesday, January 29, 2019 12:03 AM To: [email protected] Subject: Re: [BITX20] display not working I had

Iv e ordered a new display but ive lost sound also Sent from Mail for Windows 10 Sent: Tuesday, January 29, 2019 12:03 AM To: [email protected] Subject: Re: [BITX20] display not working I had similar

I had similar problems, I changed the display!

also, be aware you need nanos without the pins soldered in. the way its mounted you have to put the pins reverse to normal. Chris

Removed the aduino from the main board and used the usb. It lit up as usual. Ive got a lit red led on the back and a red blinking led beside it. Still got the black blocks across the top row of the

Dan try removing the Raduino from the UBitx and powering it via the USB connector. If it boots up fine, then you could be having low supply voltage to your UBitx or just the Raduino via the main board