开云体育

开云体育

The generally accepted limit for SSB intermodulation products is a minimum of 24 dB between the lowest of the twin tones and the highest of either the third order (products immediately adjacent to the twin tones) or fifth order (products next over above and below the third order) products. My uBitx shows -12 dB at 3.6 MHz. Conditions are: 30 mVrms audio input and RV1 set for 5 watts RF output through a 4 MHz LPF. My board has the onboard PA filters removed and strapped and has the additional 45 MHz filter with 12:1 output impedance transformer in place of R27.

In order to better understand where the IMD is being introduced in the radio I started all the way back at the balanced modulator output and measured IMD at thoughtfully provided test points up through the driver output. In general, once IMD products are introduced at early stages they tend to only get worse as the signal progresses down the chain. The key to fixing it is finding the root cause as early in the process as possible.

TP17 is the output of the balanced modulator and the 12 MHz SSB filter. IMD products here were below the noise floor of my measurement configuration and I did not chase them down into the mud because they are at least 40 dB down and do not pop up through the floor.

TP16 is the output of the first bi-directional amplifier and IMD at this point measured -35 dB, already much too high and and indication of non-linearity in the amplifier that must be addressed.

TP14 is the output of the onboard 45 MHz filter following the 2nd mixer. This actually shows a slight improvement but probably within measurement error at -37 dB. This measurement pretty much exonerates the 2nd mixer as a significant contributor to the IMD issue.

TP16 is the output of the second bi-directional amp and again there is a serious deterioration in IMD with the amp adding 11 dB to the problem.

TP1 is the output of the 2nd transmit mixer (labelled 1st mixer in the text) and is the first time we see a signal at air frequency of 3.6 MHz. The mixer added 5 dB of IMD to the total.... much too much and probably indicative of low injection levels as has been stated in the past. On the other hand it is not the primary culprit by far.

TP3 is the output of the first pre-driver and of RV1 and it adds a little over 1 dB of IMD. The total IMD at this point is 5 dB less than the acceptable amount and it is only beyond this point that we are able to control power levels with RV1 which would normally be the adjustment point for controlling PA IMD. In other words we are starting out with an unacceptable signal from the low level stages and only now getting to where IMD is normally introduced. A contemporary radio would show normally show IMD levels at -45 dB or better at this point.

From this point forward, at the five watt level, the combination of pre driver, driver, and PA added 5 dB of IMD. This amount would be perfectly acceptable in most radios starting out with clean drive and would allow the total power to be? increased by RV1 adjustment to significantly higher levels.

The IMD problem is rooted first in non-linearities in both bi-directional amps and then in both mixers.

WA8TOD

?On Tue, Sep 11, 2018 at 01:37 PM, Jerry Gaffke wrote: Correction:What I wrote:<? Those two pins are pins 1 and 2 shown in the far upper right corner of the uBitx schematic.Should be>? Those two pins are pins 1 and 2 shown in the far upper LEFT corner of the uBitx schematic.

On Tue, Sep 11, 2018 at 12:10 PM, Jerry Gaffke wrote:

Fabian,
Those two pins are supposed to be shorted together on your Raduino.
Though it is kind of confusing.

Here's the schematic for the uBitx:? ??Those two pins are pins 1 and 2 shown in the far upper right corner of the uBitx schematic.Pin 2 is used to send 12v from the uBitx main board off to the Raduino.Pin 1 is not connected to anything.

Here is the schematic for the Raduino:??
What was pins 1 and 2 of the RADUINO1 connector in the uBitx schematic
are now pins 16 and 15 of the P3 connector in the lower part of the Raduino schematic.
That's unfortunate, it's much less confusing if a schematic set retains the same naming and numbering conventions.
Those two pins send 12 volts into the LM7805 regulator, which creates the 5 volt supply for the Nano.

So the uBitx main board only has 12 volts going into one of those pins, the other pin is not connected to anything.
The Raduino board has both pins shorted together (as you have shown in your picture) and this gives 12v power to the Raduino.

All is well.
?
Jerry

I suspect it is more critical that we have sufficient drive into the mixer LO port
than to have that 6dB 50 ohm pad.
This sort of thing is best evaluated by somebody with a spectrum analyzer.

A series cap plus series resistor between the si5351 and the mixer may be sufficient,
the resistor value is a compromise between sufficient drive to the mixer
and minimizing how much power we demand from si5351.
Could also add a resistor from mixer port to ground to bring source impedance there down,
though that further reduces drive available to the mixer???
? ? /g/BITX20/message/35206

The CMOS buffers previously mentioned are good down to about a 100 ohm load,
? ?/g/BITX20/message/59200
Use separate devices for each clock to avoid crosstalk, and filter Vcc well.?
If you insist on driving 50 ohms with CMOS buffers you might put two such gates in parallel:

Often you see an MMIC in that position, but we don't have to be linear here.
The diode mixers work well with a square wave.

Jerry, KE7ER

开云体育