开云体育

This is my channel with some videos about ubitx, the language is in Brazilian Portuguese. https://www.youtube.com/channel/UCEHvfCPbNvfmeqj3srgpxNw

The LDG Z-100Plus tunes with only 100mW of power.? It holds eight AA batteries internally, making it ideal for portable QRP operation.? Small, light weight and self-powered. Bert N8NN

I use my LDG Z-11ProII with an end fed wire and my Bitx40. The tuner only requires 100mW of signal to auto tune.? http://www.ldgelectronics.com/c/252/products/21/9/1?(

hi i have finished boxing up my ubitx and all working ok,not sure on michrophone as i have to shout into electret to get any power out,would it be ok to fit 5 volt regulator to supply power to normal

I have built the Bitx20 for the best part, only the final stage with IRF510 remains. Before I start building the final I would like to check if everything works fine sofar. The reception is great but

I fear the coupling is thro power line. Please try star mode power line distribution.if possible have a Inductor based "pi" filter for the independent stages in power feed. Regards MVS Sarma

Peter, please see: https://vk4pln.blogspot.com.au/2018/03/vk4pln-ubitx-add-on-boards.html

Here you go folks: https://vk4pln.blogspot.com.au/2018/03/vk4pln-ubitx-add-on-boards.html 73

I see that you have enclosed wiring in a tubing, did you twist the wires before sliding into the tubing. It seems that if you don't twist the wires or replace with shielded wiring there is a lot of

Nice job on the layout Ron. Like Mike said, try some 0.1uF caps on the 5V raduino regulator. I didn't see the 4.7K pull up resistor on pins 2&3 of the raduino either. Try another spkr direct to board

You should check out tindie.com they are set up for small sellers and more geared towards electronics than Etsy. Ralph N9WTX

Hi Everyone. I am happy with my RaduinoI2C board and the Audio Board. I havent build a HPF or LPF yet(other than prototype) but they are straight forward, still waiting on the CW filter... Now Im

Nice build Ron! I suspect you have noise from the display getting into your audio.? This may be an earth loop issue, or it may be leaking directly in to your speaker as it is shown in the photo

Not necessarily grandpa's. ?I just now noticed the signature in the image, here's more of them: ? ??https://www.pinterest.com/pin/416090453046673659/ A very famous film star from the 1920's. My

Thanks for the suggestion Nick, BTW... I’ll buy one of those boards if you sell em.? I’d considered tacking a relay onto a Hi-Per-Mite but yours would be more elegant.? Let me know.? Pete

The white panel looks like nylon.? I use sheets of that to make guards and guide for table saws, routers, etc.? Very slick stuff.? Pretty soft to machine, drill, or cut.? But makes a super slick

FB Vince. That's a great looking rig with the Pi interface. I might swap cases and do something similar? with my new uBITX instead. Could you drop me an email at mycall @ RAC.CA? I would be

All Good today.? Once the KD8CEC software was installed, finally found a newer Memory Manager. Maybe a Link in Files here for all pertinent programs, ie. uBITX Memory Manager all recent versions that

where to order this case looks great

Hi, Chop up a set of cheap in-ear headphones.... See my new board, awating delivery:?/g/BITX20/topic/14920831?p=Created,,,20,1,0,0 Ill post up pic of it installed once done. 73