开云体育

Try this old post: ? ??/g/BITX20/message/40216

It's a heat resistant tape that's flame resistant and good to 600F (intermittantly). I know it's also used with heating elements and is used by some on their 3D printers. I bought it 'cuze I have

Also I cannot read the values of the Caps due to pixelation.? Could you provided those values.

Could you provide the number of the transistor?? Yes, I am that needed.? LOL Thanks

Mine shipped same date, picked up Hyderabad 16:38 their time on the 19th - took 24 hours to get to Bangalore (got there 1646 on the 20th) and got hung up in Bangalore for some reason. Finally left

Eric, Couldn’t find your earlier link to “Cash’s video”. Could you re-post. Thanks Mike K5ESS Sent: Wednesday, February 21, 2018 12:07 PM To: [email protected] Subject: Re: [BITX20]

So do I need both the 10k ohm resistor from c1 to ground and the make before break rotary or just one or the other?

Paul: I ordered the connector shells/hoods from Tayda. "Housing Connector 2.54mm" Pins 2, 3, 4, 5, 8, 12 Part # A-826, A-827, A-828, A-829, A-832, A-835 Ordered a mix of sizes (+/- 300 total).

uBITX ordered on 12-23-2017. Received shipping email on Mon, Feb 19, 2018 5:29 am with DHL tracking number. It was delivered to me on Wed Feb 21, 2018 11:55am. That was definitely worth the

2 more things, a 10k from + of c1 to ground will stop voltage screaming to the rail while changing it with power on. if you go to a rotary make sure it is make before break and the spike wont happen.i

THE ZENERS SET THE PASS VOLTAGE OF THE 100 VOLT 10 AMP DARLINGTON. sorry caps lock. they are 1 amp devices but the transistor slaves them to 10 amp handling. i have used this ciruit fo over 40 years.

Thank you Eric, for the very valuable tips, can't wait to try it out. How do you protect the other components from the hot air? 73! George VE7WQ Wednesday, February 21, 2018, you wrote: EK> It's

If you were to measure the actual impedance, you would probably find that the transformer is reactive (imagine that! ). You might try a little capacitor across the windings to counter that. Dr.

Zeners probably wont work for this application by themselves because the loading requirements are too great. They may work as drivers for higher current transistors though. Dr. William J. Schmidt

Jerry. I was reading an article I mistook RV1 for RV2, got into a panic and before I knew it I was in the "Keeck" as we say in Scotland :-) Tiredness, panic and daftness. I will now go and stick the

Looks fine. Mine is from Michael's rated at 360w. It was $20. WalMart might even be cheaper. They're probably all nearly identical. Mine looks like the one you show except for packaging details. BTW,

Okay here's my Story. Order on December 22, late in the day. Knew it would be a while, but paid $10 for DHL delivery anyway. Fast Forward to Monday February 19, the day before yesterday. Checked

Thank you Vince, I have a roll of kapton tape here, bought it for general insulation purpose. It'l be handy for smd work then. 73! George VE7WQ Wednesday, February 21, 2018, you wrote: VV> Yes,

I'm working on a Bitx40, that was initially purchased without the Raduino; but now I have a Raduino and I need to verify that the DDS is correctly driving the mixer. On the Bitx40V3 schematic, I

Don't get me wrong, I applaud your willingness to reach in and play with your uBitx. That's what these rigs are all about. Just taking the opportunity to let others in the forum know that twiddling