开云体育

namaste, Sarma raj Your suggestion may be good, but the first thing told to a ham should be look in old pieces of equipment for something. Or go to a hamfest and see what 's there. Or the junkbox. (It

Even if some one (other than some of your own city or nation) has it.?the inter trans shipment would cost a moon. Instead you may seek for higher size smd cap at 2KV ready on ebay or aliexpress.

I heard you but you never answer my call El El vie, 14 jul 2017 a la(s) 11:43 p. m., N8DAH <Dherron@...> escribió: *“If you have a penny and I have a penny and we exchange pennies, you still

I noticed that the colors looked a little strange. It appears that with this display the colors are the complement of what was intended. I replaced all the values of the colors defined in lines 87-94

I always wanted one of those. I called for about an hour but with some random AM stations and some other 1KWers I stopped after a while. ?Just wish my CQ times were better, I am dealing with some bad

Didn't hear a blessed thing on my mcHF SDR on that frequency. I DID hear some PSK activity on 7.070, though I didn't make any contacts there. RichKC8MWG

Let me back up again: My kit came with something like 1.0 or 1.1 already installed on the nano. Right out of the box my Bitx would receive fine but not transmit. While I was waiting to try and resolve

Great! Jack, W8TEE To: [email protected] Sent: Friday, July 14, 2017 11:17 PM Subject: Re: [BITX20] W8TEE TFT /VFO BOARD - WHICH DISPLAY? #yiv3636021559 #yiv3636021559 -- _filtered #yiv3636021559

Unlikely C111 but you may have a short in your speaker jack/socket or wiring. Raj

Jack, Never mind. I added case 0x9486: and now it looks good. Mike K5ESS Sent: Friday, July 14, 2017 10:00 PM To: [email protected] Subject: Re: [BITX20] W8TEE TFT /VFO BOARD - WHICH DISPLAY? Jack, My

I thought you said you couldn't upload to the Nano. Jack, W8TEE To: [email protected] Sent: Friday, July 14, 2017 11:09 PM Subject: Re: [BITX20] Still Not Working I believe I did that before I

I believe I did that before I downloaded 1.18 into the nano. I'm guessing that if I didn't install those drivers I wouldn't have been able to download?

Opps: it should be in hex: ? g_identifier = 0x9486; To: [email protected] Sent: Friday, July 14, 2017 11:05 PM Subject: Re: [BITX20] W8TEE TFT /VFO BOARD - WHICH DISPLAY? Try forcing it. Add this line

Try forcing it. Add this line at 1333: ? g_identifier = 9486; recompile, and upload. If you see white smoke coming from...naw, just kidding. Try forcing the ID and see if one works Jack, W8TEE To:

Jack, My display looks like the bottom picture below but my display is the Mcufriend 3.5“ TFT LCD for arduino uno. It identifies as g-ID = 9486. However looking at the code around line 1335 there is

I been looking on 7,250 and 7,273 nothing on these frqs stations on 7,270 & 7,272 and a station on 7,249 I have s2 noise on my old ICOM 745 chris g0wfh

Have you tried installing the drivers that appear in the drivers subdirectory if where you installed the IDE? There are 2 EXE files to use, depending on your system. Jack, W8TEE To: [email protected]

Thanks Jack, this is my third Arduino project. I built a couple of antenna analyzers and made some changes to the code. I am by no means an expert but not afraid to get in there and see what makes it

I could hear N9ARZ, but the band must be broken between Atlanta, GA and Spiceland, IN. Too much chatter on this freq. I'll have to restring my antenna an point it North tomorrow. wrote: Andrew Krause

This is an unabashed plug: The Arduino Projects for Amateur Radio book was written for non-programming hams who want to ease into learning about the Arduino family of microcontrollers. It starts out