Kelly, I would suggest this as a pattern of equipment purchases:

1: a good DVM.? There are good ones which won't break your wallet - and you would want as good as you can find.? I've seen them with all sorts of abilities, such as a (rather low bandwidth) frequency counter, transistor tester, and cap meter.? I've heard some horror stories about Chinese products, but I've used some of their stuff and have had no problems with it.? I use a fancy Radio Shack meter which has been adequate, accurate, and precise enough - and rugged.

(Equally important to a good meter - a good soldering iron.)

2: Look for a used scope, minimum 30mhz bandwidth.? Unless you have a lot of experience with them, stick to a used (but working) analog scope.? I've seen some pretty good deals at hamfests... working condition, for under $100.? The more you know, the more useful it can be!

3: Somewhere near the top, antenna testing gear is a necessity.? If you have soldering experience, I would suggest "rolling your own".? I could point out some inexpensive pieces that can be combined together as a very effective tool.? The Handbook has some good stuff in it, the Experimental Methods in RF design book is much better.? (I combine ideas from that with arduino, and have some really useful circuits, like a wide bandwidth and very sensitive dBm meter that reports signal strength to software or spreadsheet - more than a thousand times a second.)

4: Something that receives across the bands - a general coverage receiver of some sort is (IMO) almost a necessity on a decent bench - something with at least moderate shielding and can receive WWV and so on.? Along these lines, if you work with VHF or UHF, a decent SDR dongle is cheap and can be used for all sorts of things - like checking the deviation (and spurs) on a 2m rig.? I paid less than $30 for mine (NESDR Smart)... and there are some which are better and that can go down well into the HF range (mine stops around 27mhz).?

THEN I would recommend a signal generator.? (It could be combined with #3 to do some impressive work.)? I built my own unit by combining a DDS kit with a good attenuator salvaged from a burned signal generator.? You combine them together in a single case, and shield and ground everything, you can keep leakage to a minimum and have something really useful.? For instance... have a impedance bridge with an unknown ferrite toroid on one leg (with a single loop of wire through it)... drive the thing with the signal generator (programmed, using a computer to step it through a frequency range), and watch the output with the digitizing dBm meter.? Presto - you can with a little reading and math, figure out the characteristics of the toroid!? (Especially if you have a couple of known-value caps you can throw in the circuit...)

With those, you can get really creative.

Bob

N4FBZ

_._,_._,_

Some hams I knew in Californicated were using 120 V AC plugs on their radios. However, that is a piss poor Idea, considering what that voltage can quickly do to an item made for 12VDC, should someone happen to plug it into an AC outlet.

Jerry, what do you think about this case as far as portable use?? I was a little concerned with the vents, I figure they'd make it a lot easier for foreign matter to get in there.

Rob KC4UPR

I haven't look at Farhan's code in detail, but the Adafruit library has a setRotation() call that allows you to rotate the orientation of the display. I don't know if Farhan is using it, however.

Jack, W8TEE

On Wednesday, January 15, 2020, 5:22:53 PM EST, Evan Hand <elhandjr@...> wrote:

You will need to provide the details on the uBitx: version, any extra addons, etc.?

Best choice is to just remove and reinstall the display.

73
Evan
AC9TU

--
Jack, W8TEE

QTH is in north or south hemisphere?

_._


On Wed, Jan 15, 2020 at 3:07 PM David Alexander <oldbeeman@...> wrote:

thinking about this the picture was rightside up when i first connected to as i had it in the panel and was working.

what might have happened?

dave

On 1/15/2020 1:23 PM, David Alexander wrote:

is there a way to turn the picture over on the display.

apparently?? i mounted the display upside down.

you would have thought that the?? labels would be right side up when mounted but i guess not cause the picture is wrong now.

dave k7da