|
|
Re: Version 4 bitx squealing after nextion upgrade.
MVS Sarma,
By vacate the eeprom contents using some ino I assume you mean to use the Arduino development software to load a file like "blink.ino", as opposed to the .hex files using Xloader.? Then to load in the .hex file.
Evan AC0TU
|
Re: Version 4 bitx squealing after nextion upgrade.
I take that back on the resistor. It is installed. It came preinstalled on the board I got with my case from amateurradiokits.in
|
Re: Version 4 bitx squealing after nextion upgrade.
uniflite58
, Please try to vacate the eeprom contents using some ino and then load stock version and let us see .
|
Re: Version 4 bitx squealing after nextion upgrade.
Uniflite58,
The resistor is needed even if you do not plan on CW.? The uBitx can get into CW transmit mode without the resistor.? Per the instruction from HF Signals be sure to install the 4.7k resistor between the blue and green wires from the Raduino board (NOT the main circuit board).? Insulate it and then try again.
It still may be toast, but you need the resistor connected.
Here is the link to the wire up instructions:
73
Evan
AC9TU
|
Re: Version 4 bitx squealing after nextion upgrade.
I should add that I did accidentally load the firmware for the s meter version first. I quickly noticed this was wrong and loaded the correct version.
|
Thanks everybody for the help.
Give me something more to try. ?
ED
Stay tuned
|
Re: Version 4 bitx squealing after nextion upgrade.
Thanks Evan,? The lcd is and was at full brightness. I did not have the cw resistor in place as I didn't plan on using that mode..
The rig worked fine before the upgrade. I installed the nextion then brought it to my computer and loaded the appropriate hex file for the new screen.?
Right after that is when the problem started.? I reverted back to the stock hex file and re-installed the 2 line display and the problem persists.
I think it's cooked.
|
To follow up on this, there is a calibration file on this group for the CEC firmware that will get you real darn close. I used it on my board and its close enough to work FT8 with. data only phone, no call/txt
telegram @folfyshark
On Fri, Dec 14, 2018, 5:22 PM Terence Taylor, < n6mon@...> wrote: Have an offer of help. Thanks, all!
--
----------
N5WLF, Greggory (or my nickname, Ghericoan)
General Class, Digital Radio Hobbyist
|
Re: Version 4 bitx squealing after nextion upgrade.
|
Re: Version 4 bitx squealing after nextion upgrade.
How well was your radio working before you added the nextion?
|
Re: Version 4 bitx squealing after nextion upgrade.
I would start with verifying that the dimming function is at full lcd bright.? There is a known issue with the chopping circuit on the lcd display causing audio issues.
The issue that I ran into in the upgrade was that the calibrations were all off afterwards.? I velieve this was caused by me loading the software onto another nano. Not sure the root cause, however I have read on this site that holding in the encoder button while powering up the unit will reset to factory settings.? I would try that after checking the lcd setting.
Are you sure you have the resistors CW in place and that the rig is not transmitting (I know, stupid question, however I did run into this one time with my rig.)
After insuring the the rig is not transmitting, disconnect the speaker and verify all of the settings using the CEC configuration screens.
I would also suggest that you download the CEC memory manager program in the google drive link in the following :
This is for modifying old releases to work with the memory manager, but I did find useful info on operation:
Beyond the above, I would need more information on what changed from before to after the upgraded as well as the process used to load the new programs into the nano.
73 Evan AC9TU
|
Version 4 bitx squealing after nextion upgrade.
I upgraded to a nextion 2.8 last night and its up and running properly. However, all I can hear now is a constant high pitched tone and loud squeaky scratchy sounds when tuning. Volume pot has no effect on volume. I've checked all my connections several times. If I lift the board off the standoffs it gets worse. I do have a good ground to the board.??If I unplug the nextion, the squeal goes away but receive is absolutely dead. I can barely hear the encoder ticks. Antenna is hookep up.??Any Ideas anyone?
|
Sharma,
The SPURS and HARMONICS are two different issues. In my mods and tests of 3 boards, harmonics are
cured with relay change - KT1//2/3 and that reduces the spurs too.
With change of L5/7 with Shielded SMD ONLY or 45MHz LPF ONLY the spurs are fixed but not the
harmonics.
This has been tested on 3 boards here at my lab and also demonstrated to Farhan.
I don't any need for further repeat messages of the same mods ad nauseam.
Raj
toggle quoted message
Show quoted text
At 15-12-18, you wrote: Why should we replace relays ?
I remember Ashar Farhan's findings regarding source of spurs, and he was trying to treat that section.
The earlier mod was how to remove spurs once created. People had many ways, one being relay replacement. If RF signals even now assemble with old relays, they would have a reason, right.
I suppose, it is better to wait and see the next version board and then adopt the mods with specific reference to that board.
regards
sarma
vu3zmv
|
Why should we replace relays ?
I remember Ashar Farhan's findings regarding source of spurs,? and he was trying to treat that section.
?The earlier mod was how to remove spurs once created. People had many ways, one being relay replacement. If RF signals even now assemble with old relays, they would have a reason, right.
I suppose, it is better to wait and see the next version board and then adopt the mods with specific reference to that board.
regards
sarma
vu3zmv
|
I have a bitx40 as Bill noted.? Should I have installed a different version of the software?? I'll read the instructions you posted, thanks.
73 DE KD5RYO
|
Re: uBitx RF Power Amplifier Standalone
Thank you for the information mail JuanCarlos
Satish VU2SNK
On Sat, Dec 15, 2018 at 1:04 AM Juan Carlos Berberena Glez < cubanqrp@...> wrote: Hi Guys
I am very happy with the information about the uBitx PA performance tested in Marianao, Havana Cuba by CM2KMK and CO2JT.
Heriberto(CM2KMK) redo the uBitx PA? board and tested with the Lagunero exciter with a very good work inside Cuba and with me in South West Florida(Cape Coral).
Please any concern about the layout or other question? drop an email to
cl2kmk@...
Please notice the email address is as CL and He is now as CM.
Thank you for your time.
Qrv's?
73's Jc
P.D.
WJ6C
|
|
|
Back in stock if you missed them -- David
?N8DAH
|
toggle quoted message
Show quoted text
You'll want to change the Master Calibration number, Increasing it lowers the frequency, lowering it raises the frequency.
There are a couple ways (at least) to do it.
The cut & try method is to change the number by a few hundred, save in into the uBitX, and see where it is. Then repeat until you get it where you want it. Lower the number to, say, 155500 and try it, If still to low, drop it another couple hundred, etc.
Or, you can calculate how much to change it with the formula here:?
He goes thru the theory but if you want to cut to the chase, scroll about halfway down to the examples and plug in your numbers. Then change the Master Calibration number based on you calculation, save it to the uBitX, and repeat if necessary.
Write down the Master Calibration number before you start so you can go back to it if you really mess it up.
Hope this helps...
73...? ? ?Mark? ? ?AA7TA
|
Ghericoan
_Dave_ AD0B
Raj vu2zap
Satish Chandorkar
Alan de G1FXB
N8DAH