BTW, Pat - 100uF, 47k? T=CR - mics x megs = seconds, 100 * .047 = 4.7s. Is there a threshold? or do you have around 5 seconds of gradually-increasing signal?

73, Dex

Pat, it's all said - think about it. 'Normalises' signals through the whole Rx chain once respectable level achieved, leaving it running at full gain until then. Transients knock it back till 'hang' fades out. Same as AM. Just concept, untried ...

73, Dex ZL2DEX

开云体育

For anyone using this scheme: I recall someone encountering distortion due to something in the Rx before this point. I had the thought (that still remains): why not 'feed-forward' like AM AGC? My replacement Raduino is currently en route, and I haven't yet had the chance to try this - has anyone else done so? I envisage detecting the audio level at the top of the Vol pot as this does, but taking the FET drain to Q1 base via 0.1uF and with time constants in between adjustable for fast/slow "hang". What say, folks?

73 de ZL2DEX

Ok, so it also has a resistor and a couple of caps. Anyway, here it is:



While wsjtx doesn't put a steady tone on the opposite channel from the data, it does put out data in both channels. That data is more than enough to turn the fet on and transmit. Until the other day, I was only putting out a bit over a watt into a long wire with an unun. I still managed to make several contacts with this circuit as an interface.

Vince.

--
Michigan VHF Corp.

I have an old Telex ProCom I amplified microphone that has never been used and I was thinking that it might be a good match for my BITX40.? It uses an Electret element and has a fixed level output amplifier.?? Runs off an N type battery.?? Anyone have an opinion as to whether I will overload and possibly damage the mic input circuit on the BITX ?if I used this?? Will I need a blocking capacitor since it does not require DC from the BITX?

Thanks,?? Jim?? W6yxy

开云体育

Hello
I'm thinking of trying to build an age circuit. I have ample room on the board I used to build the anti thump circuit. Does anyone have an opinion as to what is the best circuit to use? I was thinking of the VU2ESE configuration. Where is that circuit inserted into the bitx? At the volume control?

Thanks for all the help and advice.

73
Brent VE3CUS

Hello All,
Let me introduce me a little. (sorry if I'm writing faults in English, no so easy using a French corrector !)
I'm 49 years old . Electronic engineer in radiocommunication and power conversion. Amateur radio since 1990.
I'm buiding a lot of my equipmenst, last big project was a high level 2m SSB transceiver. I did a 80 m CW transceiver working from 3V to 6V (1W to 4 W).

I plan to build an kind of ubitx using the Raduino (thanks to Farhan's work !).
The difficuly will be to supply the transceiver with a 5 V USB power pack !
Of course transmit power will be limited to 1 W (linear) to 2 W at compression (the output stage of the MOSEF PA is allready working !)
Now I'm facing to the diver of the PA..no easy to ensure flat response at low voltage.

To developp at 50 Ohms is more easy to qualify each sub-circuit : simulating, testing, assembling...
I confirm the fact of using a 45 MHz Xtal filter to avoid looping back (I had this problem on a HP 8590 spectrum close to an internal IF )
It is important to load mixers at 50 Ohms on each port, or dissipate unwated products in a waste load.
LPF front of 1st mixer is very important to avoid image of FM broadcast band if you hare close to big transmitter (that's my case)!

I will continue this project as soon as I will have time ...not in stress !

Best 73 F5RCT Jmat ( ..shorter than Jean-Matthieu !)
?

Is it still possible to purchase the TFT/VFO boards for this project??

73,
-Rob
N4MN

开云体育

Randell,?

Searching for the word "error" in your listing shows that it's having trouble with the si570 library.
Could be a difference between Farhan's version of the library (he coded that several years ago) and what's currently available.
You can either dig back into the repository and find the correct (older) version of the si570 library
or you can figure out what those calls are doing and adjust the sweeperino code to work with the currently available library.

The latter might be best, you get any bug fixes and you have reason to learn about the si570 calls.

Rather than the duinovox I found a simpler circuit for interfacing data.
It consists of 3 small audio transformers (got 10 for a little over $1, a
couple of 1N4148 diodes and a 2n7000. I won a cheap ($4) USB sound card
on ebay so I built it all onto a circuit board and put a mic connector on
it to just plug into the Bitx. Next to the sound card, the mic connector
was the most expensive part.

I'll post a link to the schematic later today when I get home, unless I
can find it again sooner.

Vince.

--
Michigan VHF Corp.

Doug Hendrick's recently published a dropin pcb replacement for the 42if123. He was learning how to make boards, and this was his project.
He documented it in the qrp-tech files area, under KI6DS. Article is 42IF123Daughtercard.pdf

Looks straightforward to replicate.
dave /nt1u

There was quite a bit of interest in this over in the FB group, so thought I would consolidate and add here. The project is call the "duinovox" by KB9RLW. I built this very simple, low cost circuit and added in the bitx enclosure. The wiring for the pots and interface jacks are hanging loose just to see if it would work before drilling more holes. Also a picture is attached of my very first CQ? on 7.074, at 2 watts, and two stations replying. Serial 719 is getting a workout. If you do this, take precautions with the final irf510 because of the heat generated by the long transmissions.?

Hi all,
I'm puzzling with the Sweeperino. After many hours of trying I cannot make it working.

I took the Sweeperino software from the Razzies website

But at compiling it goes wrong, which library’s should I use, and where can I find the necessary version. I got the next failure messages:

Arduino: 1.8.1 (Windows 10), Board:"Arduino Nano, ATmega328"

?

C:\Program Files (x86)\Arduino\arduino-builder -dump-prefs -logger=machine -hardware C:\Program Files (x86)\Arduino\hardware -tools C:\Program Files (x86)\Arduino\tools-builder -tools C:\Program Files (x86)\Arduino\hardware\tools\avr -built-in-libraries C:\Program Files (x86)\Arduino\libraries -libraries C:\Users\Penningmeester\Documents\Arduino\libraries -fqbn=arduino:avr:nano:cpu=atmega328 -ide-version=10801 -build-path C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712 -warnings=none -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.avr-gcc.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -prefs=runtime.tools.avrdude.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -prefs=runtime.tools.arduinoOTA.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -verbose C:\Users\Penningmeester\AppData\Local\Temp\Temp2_sweeperino-master.zip\sweeperino-master\sweeperino_lcd\sweeperino_lcd.ino

C:\Program Files (x86)\Arduino\arduino-builder -compile -logger=machine -hardware C:\Program Files (x86)\Arduino\hardware -tools C:\Program Files (x86)\Arduino\tools-builder -tools C:\Program Files (x86)\Arduino\hardware\tools\avr -built-in-libraries C:\Program Files (x86)\Arduino\libraries -libraries C:\Users\Penningmeester\Documents\Arduino\libraries -fqbn=arduino:avr:nano:cpu=atmega328 -ide-version=10801 -build-path C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712 -warnings=none -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.avr-gcc.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -prefs=runtime.tools.avrdude.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -prefs=runtime.tools.arduinoOTA.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -verbose C:\Users\Penningmeester\AppData\Local\Temp\Temp2_sweeperino-master.zip\sweeperino-master\sweeperino_lcd\sweeperino_lcd.ino

Using board 'nano' from platform in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr

Using core 'arduino' from platform in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr

Detecting libraries used...

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\sketch\sweeperino_lcd.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\sketch\sweeperino_lcd.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\sketch\sweeperino_lcd.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\sketch\sweeperino_lcd.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\sketch\sweeperino_lcd.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "-IC:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src" "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\sketch\sweeperino_lcd.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "-IC:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src\Wire.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "-IC:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src\utility\twi.c" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR ??"-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "-IC:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src\SPI.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "-IC:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src" "C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master\Si570.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "-IC:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src" "C:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src\si5351.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "-IC:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src" "C:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src\LiquidCrystal.cpp" -o "nul"

Generating function prototypes...

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics? -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "-IC:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src" "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\sketch\sweeperino_lcd.ino.cpp" -o "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\preproc\ctags_target_for_gcc_minus_e.cpp"

"C:\Program Files (x86)\Arduino\tools-builder\ctags\5.8-arduino11/ctags" -u --language-force=c++ -f - --c++-kinds=svpf --fields=KSTtzns --line-directives "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\preproc\ctags_target_for_gcc_minus_e.cpp"

Sketch aan het compileren...

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -flto -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10801 -DARDUINO_AVR_NANO -DARDUINO_ARCH_AVR?? "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master" "-IC:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00\src" "-IC:\Program Files (x86)\Arduino\libraries\LiquidCrystal\src" "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\sketch\sweeperino_lcd.ino.cpp" -o "C:\Users\PENNIN~1\AppData\Local\Temp\arduino_build_47712\sketch\sweeperino_lcd.ino.cpp.o"

In file included from C:\Users\Penningmeester\AppData\Local\Temp\Temp2_sweeperino-master.zip\sweeperino-master\sweeperino_lcd\sweeperino_lcd.ino:3:0:

C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master/Si570.h: In function 'void setFrequency(long unsigned int)':

?

C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master/Si570.h:163:7: error: 'byte Si570::setFrequency(long unsigned int)' is private? byte setFrequency(unsigned long);

?

?????? ^

sweeperino_lcd:88: error: within this context

si570->setFrequency(f);

?

??? ?????^

?

C:\Users\Penningmeester\AppData\Local\Temp\Temp2_sweeperino-master.zip\sweeperino-master\sweeperino_lcd\sweeperino_lcd.ino: In function 'void setup()':

?

sweeperino_lcd:197: error: no matching function for call to 'Si570::Si570(long int)'

?

?? si570 = new Si570(SI570_I2C_ADDRESS, 56320000);

?

??????????????????????????????????????????????? ^

?

C:\Users\Penningmeester\AppData\Local\Temp\Temp2_sweeperino-master.zip\sweeperino-master\sweeperino_lcd\sweeperino_lcd.ino:197:48: note: candidates are:

?

In file included from C:\Users\Penningmeester\AppData\Local\Temp\Temp2_sweeperino-master.zip\sweeperino-master\sweeperino_lcd\sweeperino_lcd.ino:3:0:

?

C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master/Si570.h:95:7: note: Si570::Si570()

?

?class Si570

?

?????? ^

?

C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master/Si570.h:95:7: note:?? candidate expects 0 arguments, 1 provided

?

C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master/Si570.h:95:7: note: constexpr Si570::Si570(const Si570&)

?

C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master/Si570.h:95:7: note:?? no known conversion for argument 1 from 'long int' to 'const Si570&'

?

C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master/Si570.h:95:7: note: constexpr Si570::Si570(Si570&&)

?

C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master/Si570.h:95:7: note:? ?no known conversion for argument 1 from 'long int' to 'Si570&&'

?

sweeperino_lcd:198: error: 'class Si570' has no member named 'status'

?

?? if (si570->status == SI570_ERROR) {

?

????????????? ^

?

Bibliotheek Wire op versie 1.0 in map: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire? wordt gebruikt

Bibliotheek SPI op versie 1.0 in map: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI? wordt gebruikt

Bibliotheek ArduinoSi570-master in map: C:\Users\Penningmeester\Documents\Arduino\libraries\ArduinoSi570-master (legacy) wordt gebruikt

Bibliotheek Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00 op versie 1.1.2 in map: C:\Users\Penningmeester\Documents\Arduino\libraries\Si5351Arduino-b3124ab2564afc8e5dc0e5819689b824a1ff4a00? wordt gebruikt

Bibliotheek LiquidCrystal op versie 1.0.5 in map: C:\Program Files (x86)\Arduino\libraries\LiquidCrystal? wordt gebruikt

exit status 1

within this context.

Dutch: “wordt gebruikt” = is used

Can someone help me out? I’m just a starter from 67 with Arduino…

Rob Bleumer

Dex,

I find if I reply on Eudora without trimming the trailing text, the groups.io strips the whole thing.
If I trim below the signature and remove the dah-di-dah etc.. terminator, then the whole trailing text remains.

Raj

I am with you Jerry!

Without the relevant lines quoted, it becomes impossible to know to whom or what that reply is
about unless I read on the web. Mostly I ignore these mails.

Raj

At 05-10-2017, you wrote:

I am using the schematic from: