开云体育

Masaru Don't worry. Chrome will automatically translate it. The contents of the BFO configuration on your blog will be helpful to other uBITX Users. Be sure to change TX Mode to 3 (or 2?) In uBITX

Henning, Thank you for the information. Your data is quite informative. I have bookmarked your link. I don't have an actual radio to test against. I am hoping my ubitx will ship in the next few

Is your 12 V station power from a wall wart transformer ? Try a higher amperage rated transformer or a car battery. Bernie, KC9SGV

Thank you Lee OM. github V1.02 build has very stable and most functions there. Photo etc contents ,My blog here. http://maaberu.moe-nifty.com/howahowa/ (Sorry Japanese only) and... Japan need

Jason. Find the problem together. So far there has been no report on this issue. Regardless of the setting of TX-> RX Delay, it seems that wrong keys have been input. So I would like to ask you

Take a look at the voltages around Q13. That is a weak point as it can fail even if the rig is powered off in the presence of a nearby signal and you may see the base and emitter are at the same

I had to play with my child on the weekend so I confirmed it a little late. My opinion is the same as Mike. I've been asked about similar issues. also i have expierence similar situation. They were

I have a trouble with BITX40 kit from HFSignals. Receiver work great - i hear a lot of stations all over the world. But there are no transmission when pressing PTT. I check currencies al described in

Konstantinos Version 1.02 has not been released yet. All the sources I'm working on are in github. You can also see the 1.02 you are working on there. Too often Release could cause confusion for

Masa. Great!!! You tested everything pretty fast. 1.02 is not in release yet and is working. But you can use it. i have made none critical bug fixes and performance improvements. Wsjtx-Portable is

I had the same reports until I did the BFO adjustment. Mine is set at 11.996.100 for the best 73 Bill

Tim, please have a look on my folder (DK5LV) subfolder "LTSPICE XVII" in the BITX 20 group. I have made simulations of the AF preamp, the gain ist 46 dB.? I can confirm that the LTSPICE simulations

Hello Masa son, Thanks for sharing your info. Link for version CEC 1.02 please? 73 de Konstantinos, SV1ONW -- 73 de SV1ONW

Hi Eduardo --- where on the board do you see BURN MARKS? That would be the best clue. I have had both bitX40 and uBitx operating 25-50 feet from 2 WINLINK gateway stations for quite a while now

I tried USB Audio integration to ubitx. Inbon,cheap USB Audio(about $1) and Arduino to USB Passpower HUB. It's very good work for WSJT-X and CEC Firmware 1.02 ONLY USB 1 connector. USB MIc connects

Sounds like the settings in EEPROM are scrambled. Have you used uBITx Manager to check? If they are scrambled you can use uBITx manager to fix them too! Mike ZL1AXG

Did any one experienced this problem? After uploading the software from Ian Lee I was really happy how it behaved but that didn't last. I uploaded another version (unfortunately I don't remember which

Thank you again. My main concern was the height. 1.1 inch will clear the top for sure. Maybe I can use it's mike, built in speaker and optical encoder tuning too. Saturday, February 10, 2018,

First hand experience with fireworks! Sorry to hear.. RX working ?

Thanks a lot, Jack! Saturday, February 10, 2018, 7:51:34 PM, you wrote: JPvGI> Fast Tune works by observing the rate at which the user is turning the JPvGI> encoder. The timing and tuning rates are