开云体育

Most of this V3 board is IF and BFO and as such is well shielded by the prolific ground plane on it's single side.I like this type of layout as it avoids a lot of ground loop problems. To get up to

Hi, It's size and the lack of two sides (top ground plane) make it less than useful for my 6m project. I'm saving it for something else. I mentioned it so others may know that FAR has it. Myself

Hi The last time this item surfaced, I was selling it for a dollar a foot. I think I can do that again. It's a reel of 20 pF NP0 disc capacitors on paper tape, with 1 inch leads, 24 per foot.

Thanks Rahul Jim VE3DDY higher gain and lower NF. So the pin out is B-E-C which is different from other transistors. C-B-E L-R for other devices. For 2SC2570 you cab also substitute BFR90.91,96 or

Hi! For those going in for ver3 board , I once again repeat the mods. 1) Q1 I have used 2SC2570A a high ft cable TV transistor for higher gain and lower NF. So the pin out is B-E-C which is

The Far circuits boards are away too big for my application so I'm strongly considering a run of the CCA design by VU3WJM (Rahul). This board design is 6.5 X 4.25 inches and will fit nicely inside

Hello, This may not be of help to everyone but for North Americans it would be handy to know. FAR circuits www.farcircuits.net They have the the BIT-X board as drawn by the creator. The one I

Hi! Friends Unfortunately we have still not managed to get the BITX PCB commercialy manufactured even though it is quite cheap getting it done here. Secondly postage from India is also rather

Hi Arv, and Group, I've been looking at the CCA Version 3 by VU3WJM as it fits the 884 packset like a glove. I have to find someone who has that board available or else gear up to make my own. I've

Jim VE3DDY One of my BITX units is built on a 7 inch by 4 inch PCB, including the PTO/VFO, a Huff & Puff stabilizer, and three additional transistors for T/R power switching. It is a bit tight, but

Hi BIT-X'ers, My name is Jim and I'm new to the group. I'm a Canadian Radio Amateur and an avid experimenter. I have an old Chinese type 884 VHF radio packset into which I'd like to install a Bit-X

Hello, I have also done transverter for 2M in the past as well as 2m RX designs. A good filter for 2m can be done with 3 coils of helix design using aperture (window) coupling. Constuction is a 3

Hello, Harmonics resulting from mixer operation are not a problem if circuits are run linear with attention to correct signal levels. Attention to filtering is a requirement and at 2M leads must be

wrote: filter different Good... good question. ;-) The Yaesu FT-290R have 4 passaband filters sintonized at 144MHz with the aid of varicaps as output of mixer (it has also a ring diodes mixer), it

Hi Great to read about your BITX developments! I have one concern, though: will it be possibile to efficiently filter out unwanted harmonics +-n*10MHz at 144 MHz? I think VHF&up transceivers use

Greetings to fellows BITX'ers. The other day I was testing a VCO for the range of 144MHz with the interest of making work the BITX in 2m. The VCO oscillates from 125 to 145MHz approximately with a

http://www.hfprojects.com/projects/hfpacker/HFPackerAmp.pdf

Dear Manuel: I want to be grateful to you for your courtesy in giving me the information for the construction of the VFO and second for the advices towards the group. In the weekend I will be

I'm Sorry Carlos, but the group's language is English. You may prioritary to post in english. The mayority of others members only understand english. Good, You must compose the message in

ESTIMADO MANUEL: AL FINALIZAR CON EXITO LA CONSTRUCCION DEL BITX ME ENCONTRE CON LA DIFICULTAD DE HALLAR UN CIRCUITO VFO QUE SEA ESTABLE A ALTA FRECUENCIA. INICIALMENTE EL XCVER LO AJUSTE EN LA BANDA