开云体育

Well, I finally received a reply from hfsigs yesterday. They recommended I join this group and seek answers. Haha. I had told them in the original email I'd joined the BITX20 group on groups.io and

I will have a blog post up by the end of the week detailing how I turned my bitx40 into a dual bander. Right now it's 40/80 using only a second BPF, but the next mod will be to add a second LPF and

Simple: Minimize the LCD writes and you will be fine. I implemented a s-meter bar in a raduino like project (https://github.com/pavelmc/arduino-arcs) and oh boy... it was a mess in the RF spectrum

W8TEE, Jack, Cincinnati, apx 270 miles S of Detroit ?:>) To: [email protected] Sent: Thursday, June 8, 2017 12:17 PM Subject: Re: [BITX20] Calling all Midwesterners. KA8CSH, Vince, S.E Michigan (apx

KA8CSH, Vince, S.E Michigan (apx 30-40 mi N of Detroit) -- Michigan VHF Corp. http://www.nobucks.net/ http://www.CDupe.com/ http://www.metalworkingfun.com

W0OIC, Ed, Dubuque Iowa

Are there any designs out for modifying (replacing) the LPF and Bandpass Filters on the BITX40 so that it will work on 20 meters? Somewhere I saw something that said 20 Meter mods were on the way.

You will become a guru in not time! I presume that you are reading 0.9 amps not milliamps. 900mA is too much by itself without shouting into the mic. Possible final blown, assuming you are getting

On Thu, Jun 8, 2017 at 12:47 am, Dimitar Pavlov wrote: Yes, apart from the noise coming from the SI5351 when the frequency is updated, there is also some noise coming from the display each time it is

Thanks. I have a few to try. Some from a closing Radio Shack, but no idea what the specs are. And (somewhere... if I can find them) some from The Electronic Goldmine that are supposed to have a less

I received my Bitx40 v3 kit a couple of months ago and I've never been able to get it on the air.? I've done a lot of troubleshooting, tried updating the sketch in the Arduino twice, watched several

Hi Dimitar: I saw your comment:? (many features - many clicks ..., simple code - no clicks). and would like to you to explain how that works to me in greater detail. I know that many of us have

Can I use a Dynamic microphone? -- Regards, 73's Evan Seligmann ZS6ELI Cell: +27 83 460 7100 Skype: evan.seligs *MY HOBBY IS AMATEUR RADIO - ASK ME ABOUT IT Proud Member of: South African Radio League

Hi I had also very loud buzz and tuning clicks at start. Replace your 56 ohm resistor with inductor. First inductor i tried was too small (from old computer mobo), so nothing happened. The second one

Attach one wire to the ground then and then attach the two grounds to that wire so its less of a hassle connecting both at the jack Sent: June 8, 2017 4:31 AM To: [email protected] Subject: Re:

Jerry, I forgot to mention. The LDRs seen to have a peak response (to light) at around 550nm which is red LED light wavelenght, so a plain old red LED is good.

Jerry, The LDRs that you are looking for are the ones with the lowest ON (ie; lit-up bright resistance) resistance. The Bitx volume control pot is a 10k unit so if you are going to shunt the audio

it is same ground. I have troble with the jack connector... thanks

Do a test on ptt ground and mic ground..see if its same ground is my guess. Sent: June 7, 2017 10:37 AM To: [email protected] Subject: Re: [BITX20] Baofeng microphone mod for BITX So if you have 4

Hi all, Before, I have the same problem with other transceivers, with various DDS, and with LED/OLED displays.The tuning clicks, are the software problem, connected to refreshing frequency for