¿ªÔÆÌåÓý

Re: Bitx40 very loud, high-pitched, low frequency noise


Woody
 

¿ªÔÆÌåÓý

On 8/22/2019 20:15, SP9DEV wrote:

Would adding a very small capacitor (nano/pico order) help as well? Or would this be too small to make any difference?

And another question, does anyone know any MacGyver way to make something working as a ferrite sleeve? I don't have any right now and would like to test it as soon as possible.

Piotr,
Lower value capacitors cannot hurt, but they are only useful for Very High Frequencies.? The type of capacitor (electrolytic,? ceramic, silver mica, etc.)? have different characteristics at different frequencies. ? For example, tantalum electrolytic capacitors are typically useful at higher frequencies than aluminum electrolytic capacitors due to the lower ESR at high frequencies.? Lower capacitance ceramic or silver mica capacitors typically have lower ESR at high frequencies than do electrolytic ones. ? For the very lowest ESR, "chip" (SMD) capacitors perform best.? This is because the lead wires on other capacitors add inductance in series with the capacitor, thus increasing the ESR.? In your case. it is doubtful that going below .01 uf will be helpful.

A physically small ceramic capacitor of .1 or .01 uf should be low enough to bypass anything less than VHF frequencies or very fast transient spikes.?? Here is a reactance calculator that will give the effective series resistance (ESR) of a capacitor.? This is for an ideal capacitor and does not take into account lead length and the type (construction) of the part.


If you have any old computer cables, power supply cables, or similar that have a molded lump in the line, that is a ferrite sleeve.? Many times I have cut away the? molded plastic, pulled out the wire, and used them in my circuits.

?
Good luck!
Woody - KZ4AK

Google translate (maybe):
Kondensatory o ni?szej warto?ci nie mog? zaszkodzi?, ale s? przydatne tylko w przypadku bardzo wysokich cz?stotliwo?ci. Rodzaj kondensatora (elektrolityczny, ceramiczny, mika srebrna itp.) Ma r¨®?ne w?a?ciwo?ci przy r¨®?nych cz?stotliwo?ciach. Na przyk?ad kondensatory elektrolityczne tantalu s? zwykle u?yteczne przy wy?szych cz?stotliwo?ciach ni? aluminiowe kondensatory elektrolityczne ze wzgl?du na ni?szy ESR przy wysokich cz?stotliwo?ciach. Kondensatory ceramiczne lub srebrowe miki o ni?szej pojemno?ci zwykle maj? ni?sz? ESR przy wysokich cz?stotliwo?ciach ni? elektrolityczne. W przypadku najni?szej ESR kondensatory ?chipowe¡± (SMD) dzia?aj? najlepiej. Jest tak, poniewa? przewody o?owiane w innych kondensatorach dodaj? indukcyjno?? szeregowo do kondensatora, zwi?kszaj?c w ten spos¨®b ESR. W Twoim przypadku. w?tpliwe jest, aby p¨®j?? poni?ej .01 uf b?dzie pomocne.

Fizycznie ma?y ceramiczny kondensator .1 lub .01 uf powinien by? wystarczaj?co niski, aby omin?? cokolwiek mniejszego ni? cz?stotliwo?ci VHF lub bardzo szybkie przej?ciowe impulsy. Oto kalkulator reaktancji, kt¨®ry da efektywn? rezystancj? szeregow? (ESR) kondensatora. Dotyczy to idealnego kondensatora i nie uwzgl?dnia d?ugo?ci o?owiu oraz rodzaju (budowy) cz??ci.


Je?li masz jakie? stare kable komputerowe, kable zasilaj?ce lub podobne, kt¨®re maj? uformowany guzek w linii, jest to tuleja ferrytowa. Wiele razy odci??em uformowany plastik, wyci?gn??em drut i u?y?em ich w moich obwodach.

--

Join [email protected] to automatically receive all group messages.