开云体育

[SoftwareControlledHamRadio] Front panel matrix

K9HZ All Messages By This Member #6587 开云体育 Hey one thing here… I have to redefine the radio band structure every time I use a new version of the software to include the missing bands (e.g. 630M, 160M, 4M, 2M, 1.25M, 70cm, 33cm, 23cm).? Obviously some of these bands take hardware that is not currently present…(notably 2M-23cm). But it’s tough to work on the hardware for those bands when the bands keep disappearing! ? Dr. William J. Schmidt - K9HZ J62K(J68HZ) 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois ? Owner – Operator Villa Grand Piton – J68HZ Soufriere, St. Lucia W.I. Rent it: ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ? toggle quoted message Show quoted text From: [email protected] <[email protected]> On Behalf Of Oliver KI3P via groups.io Sent: Saturday, May 31, 2025 9:08 AM To: [email protected] Subject: Re: [SoftwareControlledHamRadio] Front panel matrix ? It matches this button layout: ? -------- Original Message -------- On 5/31/25 9:37 AM, Tim via groups.io wrote: TNX Is that the same as picture on front of book? I have Justin's case and the labels on case are different. I believe I can cross reference code to picture in book and figure out changes. Tim W4YN
jerry-KF6VB All Messages By This Member #6589 On 2025-05-31 09:14, K9HZ wrote: Hey one thing here… I have to redefine the radio band structure every time I use a new version of the software to include the missing bands (e.g. 630M, 160M, 4M, 2M, 1.25M, 70cm, 33cm, 23cm). Obviously some of these bands take hardware that is not currently present…(notably 2M-23cm). But it’s tough to work on the hardware for those bands when the bands keep disappearing! *** Indeed. And every time I load new software, I have to redo the support for my linear. For those unimplemented bands - maybe a #define? - Jerry, KF6VB
K9HZ All Messages By This Member #6591 开云体育 As long as its consistent... it should not matter... ? I designed the LPF for this set (which is the Kenwood/ Elecraft/ Yaesu/ etc. standard): ? But somehow that got twisted.? These standards are important because there is a connector on the LPF control board to send these to the back panel to operate devices external to the radio like antenna switches, filters, amps, etc. that also have programming for these standards.? ? ? The average person should not have to worry about this… because when connected, it just works… ? ? ? ? Dr. William J. Schmidt - K9HZ J62K(J68HZ) 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois ? Owner – Operator Villa Grand Piton – J68HZ Soufriere, St. Lucia W.I. Rent it: www.VillaGrandPiton.com ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ? toggle quoted message Show quoted text -----Original Message----- From: [email protected] <[email protected]> On Behalf Of jerry-KF6VB Sent: Saturday, May 31, 2025 12:02 PM To: [email protected] Cc: [email protected] Subject: Re: [SoftwareControlledHamRadio] Front panel matrix ? On 2025-05-31 09:14, K9HZ wrote: > Hey one thing here… I have to redefine the radio band structure every > time I use a new version of the software to include the missing bands > (e.g. 630M, 160M, 4M, 2M, 1.25M, 70cm, 33cm, 23cm).? Obviously some of > these bands take hardware that is not currently present…(notably > 2M-23cm). But it’s tough to work on the hardware for those bands when > the bands keep disappearing! ? *** Indeed.? And every time I load new software, I have to redo the support for my linear.? For those unimplemented bands - maybe a #define? ? ???????????????????? - Jerry, KF6VB ? ? ? ?

Previous Topic Next Topic