开云体育

Easy metal production facilities

K9HZ All Messages By This Member #6040 开云体育 Well… this is interesting:? ? Wonder what is would cost to make a case for the T41 ? ? ? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois ? Owner – Operator Villa Grand Piton – J68HZ Soufriere, St. Lucia W.I. Rent it: ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ?
jerry-KF6VB All Messages By This Member #6041 On 2025-02-11 08:13, K9HZ wrote: Well… this is interesting: Laser Cutting and Sheet Metal Services \| OSH Cut [1] Wonder what is would cost to make a case for the T41 ? *** My guess is ...if you have to ask... I was looking at OSHpark board service. For the same deal as $2 from JLCPCB, their price was $80. Except only 3 boards instead of 5. - Jerry, KF6VB
K9HZ All Messages By This Member #6042 开云体育 Figgered that because OSH Park for PCBs is insanely expensive… ? ? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois ? Owner – Operator Villa Grand Piton – J68HZ Soufriere, St. Lucia W.I. Rent it: ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ? toggle quoted message Show quoted text From: [email protected] <[email protected]> On Behalf Of jerry-KF6VB Sent: Tuesday, February 11, 2025 10:24 AM To: [email protected] Cc: K9HZ <bill@...> Subject: Re: [AmateurRadioBuilders] Easy metal production facilities ? On 2025-02-11 08:13, K9HZ wrote: Well… this is interesting: Laser Cutting and Sheet Metal Services \| OSH Cut [1] Wonder what is would cost to make a case for the T41 ? *** My guess is ...if you have to ask... I was looking at OSHpark board service. For the same deal as $2 from JLCPCB, their price was $80. Except only 3 boards instead of 5. - Jerry, KF6VB
Doug W All Messages By This Member #6043 On Tue, Feb 11, 2025 at 10:24 AM, jerry-KF6VB wrote: *** My guess is ...if you have to ask... ? Actually it doesn't look that bad.? A while ago I cobbled together a slimmed down face plate to fit on a smaller printer bed and just uploaded it to oshcut to see what I'd get.? The powder coat set up fee adds quite a bit if you go that route but if someone really wants it and is willing to put together a group buy, by the time you get to about 10 pieces the powder coat price with setup drops to about the same as the raw or deburred single options. ? ? ?
K9HZ All Messages By This Member #6044 开云体育 Huh… I’m gonna have to check this out… ? ? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois ? Owner – Operator Villa Grand Piton – J68HZ Soufriere, St. Lucia W.I. Rent it: ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ? toggle quoted message Show quoted text From: [email protected] <[email protected]> On Behalf Of Doug W via groups.io Sent: Tuesday, February 11, 2025 10:48 AM To: [email protected] Subject: Re: [AmateurRadioBuilders] Easy metal production facilities ? On Tue, Feb 11, 2025 at 10:24 AM, jerry-KF6VB wrote: *** My guess is ...if you have to ask... ? Actually it doesn't look that bad.? A while ago I cobbled together a slimmed down face plate to fit on a smaller printer bed and just uploaded it to oshcut to see what I'd get.? The powder coat set up fee adds quite a bit if you go that route but if someone really wants it and is willing to put together a group buy, by the time you get to about 10 pieces the powder coat price with setup drops to about the same as the raw or deburred single options. ? ? ?

Previous Topic Next Topic