开云体育

This is an expansion. I have ordered backup thru aliexpress. Just shipped. See in 2-3 weeks. Not a problem. $1.39 a yard rarher than $12 a foot-quite a difference I want to build V012 so waiting till

Yes, I use Kicad too… but the original files were and still are in DipTrace. Eagle has vacillated between FREE and EXPENSIVE the entire time it’s been available. I believe it’s been discontinued

A very very long time ago I used Eagle, too, until "they" decided that student/hobbyist licenses for a few 100 $ are no longer available. After continuing a while with the license I still had got, I

Yeah. Well, it’s a really good design program for small PCBs…. Eagle is better for large designs by far. Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner -

OK Bill, thanks for that. Just wondering really, but not about to spend that sort of money. (US$700 = ~AUD$950) Glenn vk3pe

Hi Glenn… Well… Its not necessarily my favorite, but Al started this by using “Diptrace”… so I bought a copy (the 1000 pin version). It’s cheap for the low pin count but gets progressively

Bill, what software are you using for the Sch and PCB's? vk3pe

Bruce… did you get the wire? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa

The following files and folders have been uploaded to the Files area of the [email protected] group. * /K9HZ T41 V010 Board Sets/T41 V010 Schematics/T41 DC Power Supply V010.dch (

K9HZ <bill@...> added folder */K9HZ T41 V011 Board Sets* --- K9HZ <bill@...> updated folder */K9HZ T41 V012 Board Sets* --- K9HZ <bill@...> updated folder */K9HZ T41 V010

Ok Lou, I’ll get you in touch with the right folks. I’m currently at a conference in Denver so this my take a couple of days… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ

Hey Bill, the developer version of sBitx was my driver to build your amp, I have not integrated it yet but would love to find the others that did it already. If you know of a thread where that was

That would be great! When you’re talking mounting something new, photographs are always a great idea!

Just wanted to clarify in case there was any misunderstanding. Thanks, Al

Ok no problem. There are others in the sBITx group that have already done it. I’ll send them your way. Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner -

In MY forum, I’m not so worried about that. I’d rather see what you are replying to. BUT PLEASE FOLLOW JACKS RULES IN HIS FORUM!!! Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ

It’s up to you. I have 2 degrees in electrical engineering and adding this amplifier to a tightly constructed SBitx version two would not be something I would be interested in trying on my own at

Test. How to avoid the previous posts? Don’t hit the show quoted text? Larry KB3CUF

The information you seek/suggest (4 points of connection and the recommended heat sink) are already in the build instructions… along with a schematic (to identify the 4 points of connection: RF IN,

So what you’ll need to do is come up with mounting and connection information for people so that it becomes a real add-on kit. Just a board by it self is not sufficient.