开云体育

  1. 7x12MiniLathe
  2. Topics

My new 4 jaw chuck for rotary table

 

Here mockup? of chuck on rotary table.??
Note 3" barstock for chuck adapter. The table is only 3" diameter?
?
The chuck 1.89" [48 mm] for small work
FYI I 5" for larger work too
?
Dave
 

Seems like a big loss on the Z axis. Easy to fix and it's a mockup anyway, right?


On Fri, Jan 24, 2025 at 2:05?AM davesmith1800 via <davesmith1=[email protected]> wrote:
Here mockup? of chuck on rotary table.??
Note 3" barstock for chuck adapter. The table is only 3" diameter?
?
The chuck 1.89" [48 mm] for small work
FYI I 5" for larger work too
?
Dave
 

I did not show zee axis.
Here is? the attachment.
?
?
Dave?
?
 

I believe the Z axis would be the height?of the milling attachment off the rotary table!

That is a big piece you picture.

On Fri, Jan 24, 2025 at 12:32?PM davesmith1800 via <davesmith1=[email protected]> wrote:
I did not show zee axis.
Here is? the attachment.
?
?
Dave?
?

Attachments:
 

Like I found out is keep simple.
I have had Rotary Table that two to put on mill. That is a pain and takes time to make a simple job.
?
If only? you need for a 5 min job and takes 45 minutes to change to table and back to the vise. It make twice if really need to ise the Rotary table.?
?
This small I chuck? up in the mill vise in a minute use small 4 jaw chuck to hold part and 10 minutes later I have a finished part.?
?
Setting up for both the mill and mini lathe There times I using the mill and need to do a quick and the mini lathe is not being used.??
?
Am also setting up for drilling for same reason.??
?
When manufacturing I do simple milling lathe had only few mills . Make a jeg and use woodruff type or keyway.
?I have use a Aloris tool post too.?
?
Photo is off the Internet NOT MY LATHE..
?
Dave?
 

Here the base for the rotary table in a real mini lathe being machined
?
Dave?
?
? *
?
 

Here's a drawing of the back plate.
?
?
?
Dave?
 

Today I machine the pilot for adapter to rotary.?
Here sise of chuck tomorrow I will machine the polit for chuck.?
Note The chuck did not come with screws I had two that fit.
?
Dave?
?
See photo
 

There's a saying on Facebook, "This isn't an airport, no need to announce your departure. " People got tired with that rudeness and just vote with their feet.


On Tue, Jan 28, 2025, 7:41?p.m. davesmith1800 via <davesmith1=[email protected]> wrote:
Today I machine the pilot for adapter to rotary.?
Here sise of chuck tomorrow I will machine the polit for chuck.?
Note The chuck did not come with screws I had two that fit.
?
Dave?
?
See photo
 

I have been Facebook since 2005 but Facebook changed in upgrade to 2007.?
?
Most ones have are trying make money that why a will walk.?
?
I am responding to your question?
?
Dave?
?
On Wed, Jan 29, 2025 at 12:57 AM, Brian wrote:

There's a saying on Facebook, "This isn't an airport, no need to announce your departure. " People got tired with that rudeness and just vote with their feet.


On Tue, Jan 28, 2025, 7:41?p.m. davesmith1800 via <davesmith1=[email protected]> wrote:
Today I machine the pilot for adapter to rotary.?
Here sise of chuck tomorrow I will machine the polit for chuck.?
Note The chuck did not come with screws I had two that fit.
?
Dave?
?
See photo
 

Here backing mount ready to drill.
?
Note the tape hold in center ?" x 20 use for holding parts in chuck like a draw bar
?
Dykem paint on ready to drill tomorrow.?
?
Dave
?
?
?
 

I'm out-I feel that davesmith1800 (if that is his real name) should have been banned by the moderators long ago. I just can't be bothered to incessantly?exposed to that brand of nonsense (what little of it I could make out due to poor English and even worse spelling). Good luck to you all-
 

I disagree. I admit I haven't been paying much attention to this thread, since I don't need to put a four jaw chuck onto rotary table. But Dave Smith seems to be serious about doing that, and he's providing drawings, photos and descriptions in his recent posts, so he's not just clowning around wasting people's time.? I agree Mr. Smith's language is irregular, but English may not be his native language to begin with.

I often see discussions here that I have no interest in whatsoever. But that doesn't mean they should be banned. It means I should shut up and hit my delete key.

Mike Taglieri?


On Wed, Jan 29, 2025, 7:48?PM Whitebear via <jmichaelsisler=[email protected]> wrote:
I'm out-I feel that davesmith1800 (if that is his real name) should have been banned by the moderators long ago. I just can't be bothered to incessantly?exposed to that brand of nonsense (what little of it I could make out due to poor English and even worse spelling). Good luck to you all-
 

Getting back to the original subject, there are some very low profile 4-jaw wood lathe chucks that work well for holding things on a rotary table. Mine lets me do light milling on my drill press.
?
?< >
?
Roy
 

开云体育

??? Dave made mention before I believe how the cancer treatments? he's had have affected his talking/typing .

animal

On 2/3/25 2:24 AM, Miket_NYC via groups.io wrote:

I disagree. I admit I haven't been paying much attention to this thread, since I don't need to put a four jaw chuck onto rotary table. But Dave Smith seems to be serious about doing that, and he's providing drawings, photos and descriptions in his recent posts, so he's not just clowning around wasting people's time.? I agree Mr. Smith's language is irregular, but English may not be his native language to begin with.

I often see discussions here that I have no interest in whatsoever. But that doesn't mean they should be banned. It means I should shut up and hit my delete key.

Mike Taglieri?


On Wed, Jan 29, 2025, 7:48?PM Whitebear via <jmichaelsisler=[email protected]> wrote:
I'm out-I feel that davesmith1800 (if that is his real name) should have been banned by the moderators long ago. I just can't be bothered to incessantly?exposed to that brand of nonsense (what little of it I could make out due to poor English and even worse spelling). Good luck to you all-

1 - 15 of 15