开云体育

howto or help

Jacques Savard All Messages By This Member #120446 A- I ahve this? vintage? setup? ? I put some? grinder? disk? put? tooo? large? for? my? normal? use? ? I? put? al x6? to male a kind? of? wheel? ? advise? is? it? good? or? a? bad? edeal ? B- someone? maybe? know? howto? drive? this? kind? of? wheel? system?? not? possible? to? dismentle? ? have to? made? some? kond? of? drive? belt ? advise? howto please jack 47 71 ? ?
Jacques Savard All Messages By This Member #120447 here? the image ? ? 20250213_101948_1_.jpg
Bruce J All Messages By This Member #120449 开云体育 Presuming it’s the big green wheel you want to drive, replace the black stone on the other side with a pulley or a direct connection to the shaft. I have a similar arbor at home, although it does have a pulley in the middle for a motor to drive it. I assume the round shaft cover in the middle covers it all around?? Might it be open at the bottom for a belt coming up from underneath? Hard to say how it’s supposed to work with only the one view, but it’s clearly an arbor meant to be driven so there’s GOT to be some way of doing that… Or is the ‘black ’stone’ just an old hard rubber wheel designed to take a flat belt? IF so it needs either shaping or replacing since a wheel like that should be slightly crowned. On Feb 14, 2025, at 8:29?AM, Jacques Savard via groups.io <jacquessavard@...> wrote: A- I ahve this? vintage? setup? ? I put some? grinder? disk? put? tooo? large? for? my? normal? use? ? I? put? al x6? to male a kind? of? wheel? ? advise? is? it? good? or? a? bad? edeal ? B- someone? maybe? know? howto? drive? this? kind? of? wheel? system?? not? possible? to? dismentle? ? have to? made? some? kond? of? drive? belt ? advise? howto please jack 47 71 ? ? --? Bruce Johnson The less a man knows about how sausages and laws are made, the easier it is to steal his vote and give him botulism.
Brian VanDragt All Messages By This Member #120450 I think there are two pulleys in the center, one is connected to the shaft, one is loose on the shaft.? A flat belt would be shifted from one to the other to either drive the shaft or not.?? Brian ? toggle quoted message Show quoted text On 02/14/2025 2:47 PM EST Bruce J via groups.io <bruce.desertrat@...> wrote: ? ? Presuming it’s the big green wheel you want to drive, replace the black stone on the other side with a pulley or a direct connection to the shaft. I have a similar arbor at home, although it does have a pulley in the middle for a motor to drive it. ? I assume the round shaft cover in the middle covers it all around?? ? Might it be open at the bottom for a belt coming up from underneath? Hard to say how it’s supposed to work with only the one view, but it’s clearly an arbor meant to be driven so there’s GOT to be some way of doing that… ? Or is the ‘black ’stone’ just an old hard rubber wheel designed to take a flat belt? IF so it needs either shaping or replacing since a wheel like that should be slightly crowned. On Feb 14, 2025, at 8:29?AM, Jacques Savard via groups.io <jacquessavard@...> wrote: A- I ahve this? vintage? setup? ? I put some? grinder? disk? put? tooo? large? for? my? normal? use? ? I? put? al x6? to male a kind? of? wheel? ? advise? is? it? good? or? a? bad? edeal ? B- someone? maybe? know? howto? drive? this? kind? of? wheel? system?? not? possible? to? dismentle? ? have to? made? some? kond? of? drive? belt ? advise? howto please jack 47 71 ? ? --? Bruce Johnson The less a man knows about how sausages and laws are made, the easier it is to steal his vote and give him botulism.
Gary Anderson All Messages By This Member #120451 Looks like a fast and loose pulley drive to me too Brian.? ?From back in the days where you had multiple tools running off one power source, and you didn't turn on/off that power based on what tools you were using. -Gary
Phil All Messages By This Member #120454 It does look like it takes a small flat belt Maybe 1 1/2-2 inches wide. These can be found online with varying lengths and widths. It has to be disassembled to get a belt on it. You can also buy small flat belt pulleys online, Amazon I believe has them The unit can then be powered by a half horse electric motor and whatever wheels that fit the shaft OD can be utilized. Best of luck One of the things I really like about these old set ups is that they are very quiet compared to the usual bench grinding. Sent from ProtonMail, Swiss-based encrypted email. Sent from Proton Mail Android toggle quoted message Show quoted text -------- Original Message -------- On 2/14/25 5:37 PM, Gary Anderson via groups.io wrote: Looks like a fast and loose pulley drive to me too Brian.? ?From back in the days where you had multiple tools running off one power source, and you didn't turn on/off that power based on what tools you were using. -Gary
Gary Anderson All Messages By This Member #120455 I don't think one could fit an endless belt on this one.? ?Need to lace the belt.? -Gary ? On Fri, Feb 14, 2025 at 06:03 PM, Phil wrote: toggle quoted message Show quoted text It has to be disassembled to get a belt on it.
mario mohl All Messages By This Member #120459 Both center sections appear to be crowned, so that would be where to place a flat belt.? Not possible to dismantle sounds suspicious but you?e looking at it and we are not. If no dismantling to install a flat belt, I would turn a flange/pulley combination and place that on the inside of either?wheel so a V-belt can be used. toggle quoted message Show quoted text On Fri, Feb 14, 2025 at 9:29?AM Jacques Savard via <jacquessavard=[email protected]> wrote: A- I ahve this? vintage? setup? ? I put some? grinder? disk? put? tooo? large? for? my? normal? use? ? I? put? al x6? to male a kind? of? wheel? ? advise? is? it? good? or? a? bad? edeal ? B- someone? maybe? know? howto? drive? this? kind? of? wheel? system?? not? possible? to? dismentle? ? have to? made? some? kond? of? drive? belt ? advise? howto please jack 47 71 ? ?
Jacques Savard All Messages By This Member #120460 OK THANK? ?i AM? HAPPY? TO LEARN? THAT? IS? A X2? WHELL POUR? CENTRAL POWER? LIKE? i SEE? BEFAORE? FOR? SIWING? ?INDUXTRY ? BUT NOW? IS? IT POSSIBLE? TO HAVE A SPLIT? POLLY? TO PUT? AT? CENTER ? JACK 47 71 ? ?
Jacques Savard All Messages By This Member #120477 ? ok I think? I have x2? solution 1- make polly? whit? the? nut? very lilltle? poly? about 1 inch? 2.-? the? shaft are abour 5/8? inch? and? I? have? ?poly of 1/2 inch? inside? but? not? able? to make it? fit? on this kind of? shaft ? phot? show? all? the problem? ? some? solution? maybe ? ? nut poully.jpg poulie.jpg
Pierre-Raymond Rondelle All Messages By This Member #120478 开云体育 plisse, voraite in french aiv' ry bodi antersdand. tink u On 22.02.25 21:38, Jacques Savard via groups.io wrote: toggle quoted message Show quoted text ? ok I think? I have x2? solution 1- make polly? whit? the? nut? very lilltle? poly? about 1 inch? 2.-? the? shaft are abour 5/8? inch? and? I? have? ?poly of 1/2 inch? inside? but? not? able? to make it? fit? on this kind of? shaft ? phot? show? all? the problem? ? some? solution? maybe ? ? Attachments: nut poully.jpg poulie.jpg
Jacques Savard All Messages By This Member #120479 pl ? what? do you? thing? about? use? a? grinder? to make a poley? whit? the nut ? is it a good? or bad? ?way? to fix? my problem? ? ? some body? do that? before ? ? jack 47 71 ? ?
mario mohl All Messages By This Member #120480 You have a lathe, no need for the grinder On Thu, Feb 27, 2025 at 10:28?AM Jacques Savard via <jacquessavard=[email protected]> wrote: toggle quoted message Show quoted text pl ? what? do you? thing? about? use? a? grinder? to make a poley? whit? the nut ? is it a good? or bad? ?way? to fix? my problem? ? ? some body? do that? before ? ? jack 47 71 ? ?

Previous Topic Next Topic