Locked
Re: HOW TO KILL A TOPIC Re: [7x12MiniLathe] ANSWER TO GUIDE RULE - OT
So all some one has to is press the button in the?Upper right hand corner as shown in photo below. I saw botton but did not know how simple it is I has wasted my time try with that button anyone can
By
davesmith1800
·
#120350
·
|
Re: My new 4 jaw chuck for rotary table
Today I machine the pilot for adapter to rotary. Here sise of chuck tomorrow I will machine the polit for chuck. Note The chuck did not come with screws I had two that fit. Dave See photo
By
davesmith1800
·
#120349
·
|
Locked
Re: HOW TO KILL A TOPIC Re: [7x12MiniLathe] ANSWER TO GUIDE RULE - OT
Thank you I did not know *So if does do not want read or get email from topic just click and be happy.* *Dave*
By
davesmith1800
·
#120348
·
|
Locked
Re: HOW TO KILL A TOPIC Re: [7x12MiniLathe] ANSWER TO GUIDE RULE - OT
At the bottom of the message is a link titled ¡°mute this topic¡±. Click on it and it will take you to the groups.io page where you can mute the topic. Stan
By
Stan Gammons
·
#120347
·
|
Locked
Re: HOW TO KILL A TOPIC Re: [7x12MiniLathe] ANSWER TO GUIDE RULE - OT
We have members leaving. To little to talke about is basic reason. Most do not cancel they just not to come back. I am doing my part by posting on how adding tooling to my mini lathe. *So what are
By
davesmith1800
·
#120346
·
|
Locked
Re: HOW TO KILL A TOPIC Re: [7x12MiniLathe] ANSWER TO GUIDE RULE - OT
What does that mean? Dave
By
davesmith1800
·
#120345
·
|
Locked
HOW TO KILL A TOPIC Re: [7x12MiniLathe] ANSWER TO GUIDE RULE - OT
The title is clear. I'm fed off this useless topic. Thank you. _._,_._,_
By
Pierre-Raymond Rondelle
·
#120344
·
|
Re: ANSWER TO GUIDE RULE - OT
All that stuff is covered in the group guidelines which I get just about every month from a bunch of the groups that I'm in including this one . animal
By
mike allen
·
#120343
·
|
Re: ANSWER TO GUIDE RULE - OT
I think are same page ( Common sense, reasonableness and practicality, nothing more is needed. ) This all that is need. I like have said is pass {after mini lathe setup what is next step} Dave
By
davesmith1800
·
#120342
·
|
Re: ANSWER TO GUIDE RULE - OT
Exactly what is really needed. Common sense, reasonableness and practicality, nothing more is needed. Best regards David
By
David Wiseman
·
#120341
·
|
Re: ANSWER TO GUIDE RULE - OT
The problem with just saying *only* post regarding a mini lathe is After you have and have ask or read itea about a mini lathes.? There nothing left to talke about. *So group could go months or some
By
davesmith1800
·
#120340
·
|
Re: My new 4 jaw chuck for rotary table
Here's a drawing of the back plate. Dave
By
davesmith1800
·
#120339
·
|
Re: My new 4 jaw chuck for rotary table
Here the base for the rotary table in a real mini lathe being machined Dave *
By
davesmith1800
·
#120338
·
|
Re: My new 4 jaw chuck for rotary table
Like I found out is keep simple. I have had Rotary Table that two to put on mill. That is a pain and takes time to make a simple job. If only? you need for a 5 min job and takes 45 minutes to change
By
davesmith1800
·
#120337
·
|
Re: My new 4 jaw chuck for rotary table
I believe the Z axis would be the height of the milling attachment off the rotary table! That is a big piece you picture. [email protected]> wrote:
By
Ralph Hulslander
·
#120336
·
|
Re: ANSWER TO GUIDE RULE - OT
Each and every member of this group got the *TERMS OF USE* email on Jan1. It said, in part: TERMS OF USE -- How the 7x12 Group Operates *<snip>* To help achieve those goals, the following rules govern
By
BuffaloJohn
·
#120335
·
|
Re: ANSWER TO GUIDE RULE - OT
Hi guys. Sorry to come to this a bit late, I have 2 points though. * I¡¯m not sure what the problem is, as anyone can add OT to the title, as I have done. So why the continuing debate ??? * I am
By
Ellis Cory
·
#120334
·
|
Re: My new 4 jaw chuck for rotary table
I did not show zee axis. Here is? the attachment. Dave
By
davesmith1800
·
#120333
·
|
Re: My new 4 jaw chuck for rotary table
Seems like a big loss on the Z axis. Easy to fix and it's a mockup anyway, right? [email protected]> wrote:
By
mario mohl
·
#120332
·
|
Locked
Re: ANSWER TO GUIDE RULE
I forgot rotary table. If rotary table goes a mill it is OT. But if goes Mini lathe it is $&#^$ I guess it depends on if you interested read a about putting on a mini lathe if on topic or off. If do
By
davesmith1800
·
#120331
·
|